manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 32

ENGINE - 1NZ-FE ENGINE

271EG45

Alumina

Dilation Layer

Alumina

Atmosphere

Platinum 
Electrode

Heater

Sensor Element (Zirconia)

Heater

Platinum 
Electrode

Atmosphere

Sensor Element 
(Zirconia)

Planer Type Air Fuel Ratio Sensor

Cup Type Heated Oxygen Sensor

204EG54

Temperature Sensing 
Element

Platinum Hot-wire 
Element

Air Flow

Intake Air 
Temperature Sensor

EG-33

2) Construction

The basic construction of the air fuel ratio sensor and heated oxygen sensor is the same. However, they
are divided into the cup type and the planar type, according to the different types of heater construction
that are used.

The cup type sensor contains a sensor element that surrounds a heater.

The planer type sensor uses alumina, which excels in heat conductivity and insulation, to integrate a
sensor element with a heater, thus realizing the excellent warm-up performance of the sensor.

 Warm-up Specification 

Sensor Type

Planer

Cup Type

Warm-up Time

Approx. 10 sec.

Approx. 30 sec.

Mass Air Flow Meter

The compact and lightweight mass air flow meter, which is a plug-in type, allows a portion of the intake
air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air,
the detection precision is ensured and the intake air resistance is reduced.

This mass air flow meter has a built-in intake air temperature sensor.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands