manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 33

ENGINE - 1NZ-FE ENGINE

00REG09Y

230LX12

238EG79

Throttle Body

Throttle Position 
Sensor Portion

Magnetic
Yoke

Hall IC

Cross Section

Throttle Position
Sensor

Magnetic Yoke

Hall
IC

Hall
IC

VTA1

E

VC

VTA2

ECM

Output 
Voltage

V

0

5

Throttle 
Valve 
Fully Close

Throttle 
Valve 
Fully Open

90

Throttle Valve Opening Angle

VTA2

VTA1

Service Tip

The inspection method differs from the conventional contact type throttle position sensor because
this non-contact type sensor uses a Hall IC.
For details, refer to the 2006 Yaris Repair Manual (Pub. No. RM00R0U).

EG-34

Throttle Position Sensor

The throttle position sensor is mounted on the throttle body to detect the opening angle of the throttle valve.
The throttle position sensor converts the magnetic flux density that changes when the magnetic yoke
(located on the same axis as the throttle shaft) rotates around the Hall IC into electric signals to operate the
throttle control motor.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands