manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 4

ENGINE - 1NZ-FE ENGINE

247EG03

EX

Injector

IN

Water Jacket

Taper Squish

193EG05

247EG04

Bore Center

Crankshaft Center

Crankshaft
Center

Maximum
Pressure

Offset Crankshaft

Center Crankshaft

EG-5

ENGINE PROPER

1. Cylinder Head

The injectors are installed in the cylinder head to reduce the distance from injector to intake valve, thus
it prevents the fuel from adhering to the intake port walls, and reduce exhaust emissions.

The routing of the water jacket in the cylinder head is optimized to achieve high cooling performance.

Through the use of the taper squish combustion chamber, the engine’s knocking resistance and fuel
efficiency have been improved.

2. Cylinder Block

Lightweight aluminum alloy is used for the cylinder block.

Through the use of the offset crankshaft, the bore center is shifted 12 mm (0.472 in.) towards the intake,
in relation to the crankshaft center. Thus, the side force to cylinder wall is reduced when the maximum
pressure is applied, which contributes to fuel economy.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands