manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 12

ENGINE - 1NZ-FE ENGINE

EG-13

 Engine Coolant Specifications 

Engine
Coolant

Type

TOYOTA genuine Super Long Life
Coolant (SLLC) or similar high quality
ethylene glycol based non-silicate,
non-amine, non-nitrite and non-borate
coolant with long-life hybrid organic acid
technology (coolant with long-life hybrid
organic acid technology is a combination
of low phosphates and organic acids.) Do
not use plain water alone.

Color

Pink

Capacity

M / T

4.8 (5.1, 4.2)

Capacity
Liters (US qts, Imp. qts)

A / T

4.7 (5.0, 4.1)

Maintenance Intervals

First Time

100,000 miles (160,000 km)

Maintenance Intervals

Subsequent

Every 50,000 miles (80,000 km)

Thermostat

Opening Temperature

C (

F)

80 - 84 (176 - 183)

SLLC is pre-mixed (the U.S.A. models: 50 % coolant and 50 % deionized water, the Canada. models:
55 % coolant and 45 % deionized water). Therefore, no dilution is needed when SLLC in the vehicle is
added or replaced.

If LLC is mixed with SLLC, the interval for LLC (ever 40,000 km / 24,000 miles or 24 months) should
be used.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands