manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 31

ENGINE - 1NZ-FE ENGINE

00REG21Y

D13N11

Air Fuel
Ratio
Sensor

A1A+

(3.3V)

A1A-

(2.9V)

ECM

Air Fuel Ratio Sensor Circuit

Heated Oxygen Sensor Circuit

Heated
Oxygen
Sensor

OX1B

EX1B

ECM

4.2

2.2

1

0.1

Air Fuel Ratio 
Sensor Output (V)*

Heated Oxygen 
Sensor Output (V)

11 (Rich)

14.7

Air Fuel Ratio

19 (Lean)

: Air Fuel Ratio Sensor
: Heated Oxygen Sensor

EG-32

Air Fuel Ratio Sensor and Heated Oxygen Sensor

1) General

The air fuel ratio sensor and heated oxygen sensor differ in output characteristics.

Approximately 0.4V is constantly applied to the air fuel ratio sensor, which outputs an amperage that
varies in accordance with the oxygen concentration in the exhaust emission. The ECM converts the
changes in the output amperage into voltage in order to linearly detect the present air-fuel ratio.

The output voltage of the heated oxygen sensor changes in accordance with the oxygen concentration
in the exhaust emission. The ECM uses this output voltage to determine whether the present air-fuel
ratio is richer or leaner than the stoichiometric air-fuel ratio.

*: This calculation value is used internally in the ECM, and is not an ECM terminal voltage.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands