manualshive.com logo in svg

Toyota 1NZ-FE, User Manual

Share
Download
Toyota 1NZ-FE User Manual Download Page 39

ENGINE - 1NZ-FE ENGINE

199EG47

ECM

Accelerator Pedal
Position Sensor

Main

Sub

Accelerator Pedal

Throttle Body

Main

Sub

Throttle
Position
Sensor

Throttle
Valve

Return 
Spring

Throttle
Control
Motor

Injectors

Ignition Coil

Return to 
Prescribed Angle

EG-40

Fail-Safe of Throttle Position Sensor

The throttle position sensor is comprised of two (main, sub) sensor circuits. If a malfunction occurs in
either one or both of the sensor circuits, the ECM detects the abnormal signal voltage difference between
these two sensor circuits, cuts off the current to the throttle control motor, and switches to the limp mode.
Then, the force of the return spring causes the throttle valve to return and stay at the prescribed opening
angle. At this time, the vehicle can be driven in the limp mode while the engine output is regulated
through the control of the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the
accelerator opening.

The same control as above is effected if the ECM detects a malfunction in the throttle control motor
system.

Summary of Contents for 1NZ-FE




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands