Toshiba TLCS-900 Series Manual Download Page 72 | Manualshive

Page: 72 / 178

background image

72

TOSHIBA CORPORATION

TMP96C141AF

➀

Prescaler

Generates input clocks dedicated to PWM timers by
further dividing the fundamental clock (fc) after it has
been divided by 2 (fc/2). Since the register used to
control the prescaler is the same as the one for other
timers, the prescaler cannot be operated indepen-
dently.

The PWM timer uses three input clocks:

φ

/P1,

φ

/P4,

and

φ

/P16.

Like the 9-bit prescaler described in the 8-bit timer
section, this prescaler can be counted/stopped using
bit 7 <PRRUN> of the timer operation control register
TRUN. Setting <PRRUN> to 1 starts counting; setting
it to 0 zero-clears and stops counting. Resetting clears
<PRRUN> to 0, which clears and stops the prescaler.

Figure 3.8 (2). Prescaler

Dedicated Prescaler Cycle

16MHz

20MHz

φ

P1

(4/fc)

250ns

200ns

φ

P4 (16/fc)

1

µ

s

800ns

φ

P16 (64/fc)

4

µ

s

3.2

µ

sc

➁

Up-counter

An 8-bit binary counter which counts up using the
input clock specified by PWM mode register (P0MOD
or P1MOD).
The input clock for the PWM0/PWM1 is selected from
the internal clocks

φ

P1,

φ

P4, and

φ

P16 (PWM dedi-

cated prescaler output) depending on the value set in
the P0MOD/P1MOD register.
Operating mode is also set by P0MOD and P1MOD
registers. At reset, they are initialized to P0MOD
<PWM0M> = 0 and P1MOD <PWM1M> = 0, thus, the
up-counter is in PWM mode. In PWM mode, the up-
counter is cleared when a 2

n

- 1 overflow occurs; in

timer mode, the up-counter is cleared at compare and

match.
Count/stop and clear of the up-counter can be con-
trolled for each PWM timer using the timer operation
control register TRUN. Resetting clears all up-counters
and stops timers.

➂

Timer registers

Two 8-bit registers used for setting an interval time.
When the value set in the timer registers (TREG 2 and
3) matches the value in the up-counter, the match
detect signal of the comparator becomes active.
Timer registers TREG2 and TREG3 are each paired
with register buffer to make a double buffer structure.

«
...
70
71
72
73
74
...
»

Summary of Contents for TLCS-900 Series



















































































































































































Reviews:

No comments

Related manuals for TLCS-900 Series

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: Federal Signal Corporation Pages: 34

Brand: Vacon Pages: 50

Brand: Samson Pages: 44

Brand: Hansen Pages: 12

Brand: Italtecnica Pages: 16

MODACT MTNED 15

Brand: ZPA Pecky, a.s. Pages: 48

Brand: W.E.ST. Pages: 34

Smart Antenna Selector

Brand: cnsat Pages: 14

COMPAX 02 Series

Brand: Parker Pages: 242

Brand: Danfoss Pages: 2

Brand: Ledj Pages: 12

Brand: Trio Pages: 8

Botex DMX RDM Tester

Brand: thomann Pages: 80

AQ Logic Series

Brand: Bernard Controls Pages: 88

Brand: LAE electronic Pages: 3

Brand: E-MAGA Interconnect Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands