Toshiba Surveillix ESV16 User Manual Download Page 23

Page: 23 / 242

ESV16

User’s

Manual

Retrieve camera’s video stream

The camera list is expanded and displayed on the Live View

page:

•

Click “All” to display videos of all 16 channels

•

Click on a “Group” (ex. Group 1) to display videos from cameras

under that group in quad view

• Click on any camera to display video in single-view mode

Retrieve camera’s status

The camera list can show each camera’s current status. Each status is

represented with different colors:

Blue: Connected

Gray: Disconnected

Red: Performing event recording

Green: Recording (manual/continuous/schedule)

White: This channel is not configured with any camera

Summary of Contents for Surveillix ESV16



















































































































































































































































Search results

Summary of Contents for Surveillix ESV16

Reviews:

Related manuals for Surveillix ESV16

Brands by name

Popular brands

Toshiba Surveillix ESV16, User Manual

Search results

Summary of Contents for Surveillix ESV16

Reviews:

Related manuals for Surveillix ESV16

Brands by name

Popular brands