Toshiba Strata CIX IP5000 Series Page 180 User Manual Download

Page: 180 / 216

Administrator Programming

IP5131-SDL Settings

162

Strata CIX IP5000-series Telephone UG 04/09

Backlight Mode Screen

1. From the IP Configurations menu, select Others > BL

Mode. The Backlight Mode screen displays.

2. Choose Always Off, Always On or On-Demand

softkey to setup when you would like to use the
backlight.

3. Press the Set soft key to accept the change.



...or press the Cancel soft key to cancel the change and
go to the Other Settings screen.

Backlight Timer

1. From the IP Configurations menu, select Others > BL

Timer. The Backlight Timer Value x10sec screen
displays (shown right).

2. Enter the New Timer value to change the setting.

Note

Use the dial pad to enter a value of (1~30), where
1=10 seconds and 30=300 seconds.

3. Press the Set soft key to accept the change



...or press the Cancel soft key to cancel the change and
go to the Other Setting screen.

Backlight Brightness

1. From the IP Configurations menu, select Others > BL

Bright. The Backlight Bright screen displays (shown
right).

2. Enter the New Brightness value to change the setting.

Note

Use the dial pad to enter a value of (1~3).

3. Press the Set soft key to accept the change



...or press the Cancel soft key to cancel the change and
go to the Other Setting screen.

Backlight Mode

Always Off

Always On

[Set]

[Cancel]

Config

On-demand

Backlight Timer x10sec

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

: New [1: Min - 30: Max]

Backlight Bright

Backspace = Vol-Down

[Set]

[Cancel]

Config

:Current

: New [0: Dim - 3: Bright]

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Search results

Summary of Contents for Strata CIX IP5000 Series

Reviews:

Related manuals for Strata CIX IP5000 Series

Brands by name

Popular brands

Toshiba Strata CIX IP5000 Series, User Manual

Search results

Summary of Contents for Strata CIX IP5000 Series

Reviews:

Related manuals for Strata CIX IP5000 Series

Brands by name

Popular brands