Toshiba Strata CIX IP5000 Series Page 122 User Manual Download | Manualshive

Page: 122 / 216

background image

ADM/DSS Console

DSS Console

104

Strata CIX IP5000-series Telephone UG 04/09

DSS Console

The 60 button Direction Station
Selection (DSS) Console operates
alongside a digital telephone to provide
60 (up to 180) additional buttons (shown
right).

The 60 programmable feature buttons
can be assigned as CO line, extension,
DSS, One Touch Speed Dial or any other
flexible feature.

The IDM5060 (IP DSS module) console
uses dual red and green LEDs to show
call and feature status.

DSS Buttons

DSS buttons can appear on both the ADM and DSS Console. Each DSS button is
associated with a particular station in your telephone system. DSS buttons can transfer
an outside call to the associated station or make a direct call to the associated station.

The DSS LED lights steady red when the station associated with the DSS button is
ringing, busy on a call, or is idle, but all appearances of the station’s extensions are
busy or in-use by other stations. When the associated DSS button is in the Do Not
Disturb mode, the LED blinks red at a slow rate.

DSS buttons cannot directly call station Phantom extension numbers, Distributed
Hunt Group Directory Numbers, or ACD Groups. DSS buttons may be configured as
One Touch Buttons that may be programmed to call these destinations.

Calling a Station



To call a station’s extension from either a DSS console or a ADM, press the DSS
associated with the station.

A station call with a DSS button can be made on-hook or off-hook, and with Voice
First or Tone signaling. After pressing the button, treat the call like any other
station call made from an IP telephone.

«
...
120
121
122
123
124
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: Yealink Pages: 87

Brand: Samsung Pages: 22

Brand: TCL Pages: 34

Brand: TCL Pages: 38

Brand: TCL Pages: 26

Brand: TCL Pages: 10

Redmi Note 10 JE

Brand: Xiaomi Pages: 10

Brand: Cricket Pages: 12

Brand: Manta Pages: 28

Brand: ATCOM Pages: 10

Brand: NEFFOS Pages: 69

Brand: Grandstream Networks Pages: 53

Brand: Nordmende Pages: 40

Brand: 3Skypephone Pages: 36

Brand: Samsung Pages: 193

Brand: Samsung Pages: 259

Brand: Samsung Pages: 365

SGH-T519 - Trace Cell Phone

Brand: Samsung Pages: 210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands