Toshiba Strata CIX IP5000 Series Page 92 User Manual Download | Manualshive

Page: 92 / 216

background image

Feature Operations

Override Calls

74

Strata CIX IP5000-series Telephone UG 04/09

Override Calls

The available override features are:

•

Busy Override

•

Do Not Disturb Override

•

Executive Override

•

Destination Restriction/Traveling Class Override

•

Class of Service Override

•

Privacy Override

Busy Override

Ring Over Busy Override enables you to send a muted ring tone to a busy station to
indicate a call is waiting. The Busy Override (BOV) muted ring can be programmed
for each station to be two muted rings only or continued muted rings until the call is
answered. This option applies to the station receiving the muted ring. The muted ring
can be sent to the telephone speaker or to the telephone handset/headset and speaker.



To use Busy Override



After reaching a busy station, press

2

. A muted tone is heard at the busy station,

indicating that a call is waiting. The station number displays.

Do Not Disturb Override

Do Not Disturb (DND) Override lets you send a call waiting tone or ringing to a
station in DND mode to indicate that a call is coming in. Your telephone may be
programmed to block DND Override from other telephones. Your station’s LCD
shows the station you have called is in the DND mode.

OCA is possible to DND stations from stations that are programmed for DND
Override.



To use DND Override



After reaching a station in DND mode, press

2

. A tone signal is heard at the DND

station, indicating a call is coming in. On your station, the LCD shows the station
number you have overridden.

Your LCD displays

DND OVR DENY,

if the station you called denies DND

Override.

«
...
90
91
92
93
94
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 312

Brand: Panasonic Pages: 311

Brand: Smartlink Pages: 8

Brand: Yealink Pages: 19

Brand: Blu Pages: 27

Flash Mini 4031D

Brand: OneTouch Pages: 21

Brand: Sprint Pages: 238

Brand: HTC Pages: 139

Brand: Just5 Pages: 2

Brand: OUKITEL Pages: 39

Brand: Samsung Pages: 92

Brand: Samsung Pages: 132

Brand: Samsung Pages: 38

Brand: Samsung Pages: 157

Brand: Samsung Pages: 149

Brand: Samsung Pages: 154

Brand: Samsung Pages: 188

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands