Toshiba Strata CIX IP5000 Series Page 163 User Manual Download | Manualshive

Page: 163 / 216

background image

Administrator Programming

IP5131-SDL Settings

Strata CIX IP5000-series Telephone UG 04/09

145

Advanced Network Settings



To access the Advanced Network Setting screens

1. Press

Hold

+

3

+

6

+

9

(simultaneously).

2. Press Advanced softkey, the Advanced Setting screen appears.

Note

There are three screens for Advanced Settings (shown below). Use the

and

soft keys to move from one screen to another.

The general operation on the Network Settings screens is as follows:

•

To view details of an item displayed on the screens above, press the soft key that
corresponds to that item.

•

Press the Set soft key to rewrite the NV-RAM data if any setting of a minor item is
changed. The screen will move to the Resetting Selection Screen. (The Resetting
Selection Screen will be described in detail later.)

•

Press the CANCEL soft key to cancel all the intended setting changes in the minor
items and to go to the IP Configurations screen without rewriting the NV-RAM
data.

Advanced Setting

P-DNS : 0. 0. 0. 0

S-DNS : 0. 0. 0. 0

GRQ Port : 0

RRQ Port : 0

AP Addr : 0. 0. 0. 0

[Set]

(1/3)

[Cancel]

Config

Advanced Setting

Admin_U : 0. 0. 0. 0

Admin_L : 0. 0. 0. 0

User ID : 9999

Password : ****

Dynamic Port

[Set]

(2/3)

[Cancel]

Config

Advanced Setting

VLAN : Disable

Phone VLAN ID : 1

[Set]

(3/3)

[Cancel]

Config

PC Port Type: Access

PC Port VLAN ID : 1

VLAN : Disable

«
...
161
162
163
164
165
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: Haier Pages: 49

SCH-i600 Series

Brand: Samsung Pages: 12

SGH-t329 Series

Brand: Samsung Pages: 143

Brand: Palm Pages: 52

Brand: Sagem Pages: 72

Brand: Sagem Pages: 63

Brand: Sagem Pages: 77

Brand: Talkswitch Pages: 29

Brand: Talkswitch Pages: 3

Brand: QUO Pages: 5

Brand: Mobeye Pages: 28

Brand: Nortel Pages: 20

Brand: Alcatel Pages: 2

Brand: Vonino Pages: 58

Brand: Avaya Pages: 11

Brand: Sagem Pages: 97

Brand: Dotel Pages: 37

Brand: Nebi.Mobi Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands