Toshiba Strata CIX IP5000 Series Page 69 User Manual Download | Manualshive

Page: 69 / 216

background image

Feature Operations

Call Forward

Strata CIX IP5000-series Telephone UG 04/09

51

Station Call Forward Categories

You can set Call Forward for the following categories of calls. Within these
categories, you can use five different types of Call Forward Settings (as detailed in the
next section).

•

Call Forward Any Call

– Forwards any call, whether an internal call or incoming

line call.

•

Call Forward - Incoming Line

– Forward incoming line calls only.

•

Call Forward Any Call - Set for Another Station

– Enables you set forwarding

of all calls for another telephone within your telephone system.

•

Call Forward - Incoming Line Set for Another Station

– Enables you to set

forwarding of incoming line calls for another telephone within your telephone
system.

Notes

•

Call Forward Any Call and Call Forward-Incoming line can be set simultaneously
on a telephone. This allows incoming lines calls to be forwarded to a different
destination than all of the other types of calls.

•

Call Forward destinations can be set to internal destinations or an outside
telephone number.

•

You can change your forwarding destination from outside the system using the
DISA feature. See your System Administrator for DISA telephone numbers and
security code access.

Call Forward Settings

•

Call Forward All Calls

– Forwards all calls immediately.

•

Call Forward Busy/Do Not Disturb

– Forwards calls immediately when your

extension is busy or in Do Not Disturb (DND) mode.

In Tone-first systems with multiple lines, Call Forward Busy forwards calls only
when all line appearances are in use. In Voice-first systems, Call Forward Busy
forwards all calls any time your telephone is in use.

•

Call Forward - No Answer –

Forwards unanswered calls after a preset number of

rings. The preset number of rings can be set on a per user basis.

•

Call Forward Busy/Do Not Disturb/No Answer –

Forwards all calls when you are

busy, in DND mode or when you don't answer a call within a preset number of rings.

•

Call Forward Cancel

– Cancels the set Call Forward feature. Notice that each

category of Call Forward has a different code for canceling.

«
...
67
68
69
70
71
...
»

Summary of Contents for Strata CIX IP5000 Series

























































































































































































































Reviews:

No comments

Related manuals for Strata CIX IP5000 Series

Brand: iData Pages: 34

Brand: Yealink Pages: 6

Brand: Yealink Pages: 8

Brand: Sony Ericsson Pages: 2

Brand: qua Pages: 2

Brand: Alcatel Pages: 48

Brand: SLIDE Pages: 32

Brand: Linksys Pages: 5

Brand: Alcatel Pages: 56

Brand: Planet Pages: 8

Xperia Play R800A

Brand: Sony Ericsson Pages: 19

Enterprise IP Phone

Brand: Grandstream Networks Pages: 56

Brand: Quba Pages: 64

Brand: TECNO MOBILE LIMITED Pages: 41

Brand: SoftBank Pages: 352

Brand: Zte Pages: 25

Brand: Avvio Pages: 13

Brand: Avvio Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands