Toshiba D-VR18DTKB Owner'S Manual Download Page 43

Page: 43 / 96

troducti

Connecti

Bas

ic Setup

layback

Ed
iti

CR Fu

ncti

on
s

ers

Fu
nc
ti

on
Set

Recordi

If the Timer Programming did not
Complete Correctly

The error number appears on the Timer Programming
list.

The error programme will be displayed in grey
with an error number.

The error numbers indicate:

E1–E22,

E37–E39: Recording error

E23–E24: Unrecordable disc

E25/E51 : • Copy prohibited programme

• Cannot record because of the NTSC /

PAL-60 signal is received.

E26–E28: Copy prohibited programme

E29

: Disc protected

E30

: Disc full

E31

: Already recorded 99 titles (Video

mode)

E32

: Already recorded 99 titles (VR mode)

E33

: Already recorded 999 chapters

E34

: No space for Control Information

E35

: PCA (Power Calibration Area) full

E36

: Already finalised Video format disc

E40

: • There are some unrecorded parts due

the overlapped timer programmes.

• Recording did not start at the start

time.

• There is no tape in the cassette

compartment.

• Tape recording reaches to the tape

end during timer recording.

E41

: Power failure

E42

: No disc

E43

: Already 49 titles recorded (+VR mode)

E44

: Already 254 chapters recorded (+VR mode)

E45

: Copy prohibited programme

E46

: It is impossible to record additionally on

a disc recorded by other units when

setting “Make Recording Compatible”

to “OFF”. (+VR mode)

The error programme will be deleted once you
check the error in the programme list, or once you
cancel the timer-standby mode and re-enter it.

Hints for the Timer Recording

• If there is a power failure or the unit is unplugged for

more than 30 seconds, the clock setting and all
timer settings will be lost.

• If there is no disc or an unrecordable disc in the tray

(finalised DVD-RW/-R, finalised DVD+R, a fully
recorded disc, etc.), the

DVD

on the front panel

display will flash and the timer recording will not
occur. Insert a recordable disc.

• If there is no tape or a tape with a record tab is not in

the cassette compartment, the

VCR

on the front

panel display will flash and the timer recording
cannot be performed. Please insert a recordable
tape.

• When all timer recordings are complete, the

icon flashes. To play back or eject the recorded disc,
press

[TIMER SET]

, and then press

[PLAY

]

[OPEN / CLOSE

]

• The timer recording cannot be performed in DVD

and VCR at the same time. If you set two
programmings with the same channel and time both
in DVD and VCR, the programming that has priority
will be recorded.

• You cannot make any DVD operation during DVD

timer recording.

• You cannot make any VCR operation during VCR

timer recording.

• Timer recording whose recording time exceeds 12

hours cannot be made.

• When 2 or more programmes are overlapped,

“Timer programme overlapped” appears, and the
overlapped programme will be displayed in blue. To
correct the timer programme refer to “Checking,
Cancelling or Correcting the Timer Programming
Information” on page 42.

• If the Start time is earlier and the End time is later

than the current time, the recording will start
immediately after you press

[TIMER SET]

• If a videotape ends during the timer recording, the

unit will automatically stop, eject the videotape, and
turn itself off. To continue recording, insert a
recordable tape.

Priority of overlapped settings

The unit records programmes according to priority if
the timer programmes overlap.

If the starting time is same:

• The timer programming set first (PROG. 1) has

priority.

When the starting time and the ending time for
each programmes are different:

• A programme that has earlier start time has priority.