Toshiba BMS-SM1280HTLE Service Manual Download

Page: 29 / 53

Toshiba

TEST RUN

Start the system to perform operation check by following the procedure below.

12-1.Preparation

No.

Item

Details

Procedure

Peparation

Discuss with a customer to determine details of the

following.

• Select devices, and creat a system diagram

• Determine the addresses of an air conditioner and

interfaces, and creat an address management

table

• Set an IP address of Smart Manager

• Creat a setting file with the Setting File Creation

Software

Refer to the Owner’s manual of the Setting

File Creation Software.

Device installation

Install Smart Manager and the interfaces.

Refer to "INSTALLATION OF THE SMART

MANAGER" (page 12) in this manual.

For further details, refer to the Installation

manual of each device.

Wiring

Connect the power cables, ground wires, and signal

wires to Smart Manager and the interfaces.

Refer to "CONNECTION OF POWER

CABLES / EARTH WIRES /

COMMUNICATION CABLES" (page 15) in

this manual.

For further details, refer to the Installation

manual of each device.

Device setting

Set the air conditioner and the interfaces.

Set the address of the devices according to

the address management table.

Refer to "SWITCHES FOR SETTING (Smart

Manager)" (page 20) in this manual.

For further details, refer to the Installation

manual of each device.

1) Air conditioner

Address setting

2) Energy Monitoring

Relay Interface

Address setting, RS-485

termination resistance

setting

3) Digital Input / Output

Relay Interface

Address setting, RS-485

termination resistance

setting

Setting file upload

1) Upload the setting file.

For further details, refer to the setting file

creation software.

2) After the change, reset Smart Manager.

Client PC setting

Configure network and browser setting of the client

PCs.

For further details, refer to the Network

Configuration Guide of Smart Manager.

+00A10-026_01EN.book Page 29 Monday, February 14, 2011 2:46 PM

Summary of Contents for BMS-SM1280HTLE





















































Search results

Summary of Contents for BMS-SM1280HTLE

Reviews:

Related manuals for BMS-SM1280HTLE

Brands by name

Popular brands

Toshiba BMS-SM1280HTLE, Service Manual

Search results

Summary of Contents for BMS-SM1280HTLE

Reviews:

Related manuals for BMS-SM1280HTLE

Brands by name

Popular brands