Toshiba A7-ST7711 Page 191 User Manual Download | Manualshive

Page: 191 / 307

background image

191

Toshiba Utilities

Trusted Platform Module (TPM)

5.375 x 8.375 ver 2.3

Trusted Platform Module (TPM)

This section only applies to systems with TPM.

Your Toshiba computer includes the TPM (Trusted Platform
Module), which is a security encryption device for your system’s
hard disk drive. TPM is already included on your system, but
needs to be installed and enabled using the following procedures.

To install TPM:

1

Launch the TOSHIBA Application Installer from the
desktop and install the following packages:

❖

Infineon Trusted Platform Module Utility

❖

Infineon TPM (Trusted Platform Module)
Installation Guide

2

Follow the directions on your screen.

Once the TPM files have been installed, you will need to
enable the TPM feature through your system’s BIOS.

To enable TPM:

1

Power on your system while holding down the

Esc

key.

2

Press

F1

when directed.

3

Press the

PgDn

key.

4

Press the down arrow key until TPM is highlighted, then
press the space bar to change the TPM status to

Enabled

.

5

Press

Y

to save the changes.

6

Press

End

and then press

Y

to accept the changes.

Your system will restart.

For further information on how to set up and use this utility,
refer to the Infineon TPM (Trusted Platform Module)
Installation Guide.

NOTE

«
...
189
190
191
192
193
...
»

Summary of Contents for A7-ST7711




















































































































































































































































































































Reviews:

No comments

Related manuals for A7-ST7711

Brand: Razer Pages: 18

EasyNote TE69KB

Brand: Packard Bell Pages: 120

Brand: Acer Pages: 87

Brand: Lenovo Pages: 41

Brand: Lenovo Pages: 2

Brand: Lenovo Pages: 2

63664DU - ThinkPad X60 Tablet 6366

Brand: Lenovo Pages: 74

Brand: Lenovo Pages: 44

Brand: Lenovo Pages: 4

5530 Mono Laser

Brand: Dell Pages: 28

Alienware Area-51m

Brand: Dell Pages: 111

Brand: Dell Pages: 23

Alienware M14x MOBILE

Brand: Dell Pages: 52

Brand: Dell Pages: 22

Brand: Dell Pages: 1

Alienware M11x R3

Brand: Dell Pages: 42

Brand: Dell Pages: 39

Alienware M11xR2

Brand: Dell Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands