background image

4

The Giant Fw 190A-3 ARF requires a servo to operate 

the air control valve, a servo to retract the tail gear, a 
servo to steer the tail gear, a throttle servo, two fl ap 
servos, two aileron servos, two elevator servos and a 
rudder servo. Servos with a minimum of 50 oz-in [3.9kg-
cm] of torque are required for operating the elevators, 
rudder, ailerons and fl aps. We recommend that metal 
geared servos also be used. Standard servos may be 
used for the throttle and choke (the servo operated 
choke is optional). A micro servo is required to operate 
the retract air valve. An optional servo-operated kill 
switch may also be used (this is in addition to the IMAA- 
required, manually operated engine kill switch). A servo 
operated kill switch is only really necessary for engines 
that do not reliably shut off by closing the carburetor, 
but could also serve as a backup.

 Function

 

Servos required

 

Elevators  2 (min. 50 oz-in torque)

  

(Futaba

®

 S3305 

FUTM0045

)

 

Rudder  1 (min. 50 oz-in torque)

  

(Futaba 

S3305 

FUTM0045

)

 

Ailerons  2 (min. 50 oz-in torque)

  

(Futaba 

S3305 

FUTM0045

)

 

Flaps  2 (min. 50 oz-in torque)

  

(Futaba 

S3305 

FUTM0045

)

  Tail Steering  1 (min. 50 oz-in torque)
  

(Futaba 

S3305 

FUTM0045

)

 

Tail Gear  1 (min. 50 oz-in torque)

 Retract 

(Futaba 

S3305 

FUTM0045)

 Throttle 

(standard)

  

(Futaba 

S9001 

FUTM0075

)

 Retract 

(micro)

  

(Futaba 

S3102 

FUTM0034

)

 Optional 

(standard)

 Choke 

(Futaba 

S9001 

FUTM0075

)

Total 11-12 servos

A receiver battery with a minimum of 4.8V 2,400mAh is 

recommended for fl ying the Giant Fw 190A-3 ARF. The 
battery voltage should be checked before every fl ight 
to be certain it has enough “charge”.

In addition to the servos, the following items (or similar 
items) are also required. The order numbers shown in 
parentheses are for Futaba servos.

  (4) 6" Y-harness for elevator, rudder/steering, 

ailerons and fl aps (FUTM4135)

  (2) 12" [305mm] servo extension for fl aps 

(HCAM2711)

  (2) 24" [610mm] servo extension for ailerons 

(HCAM2721)

  (2) Heavy Duty switch harness (FUTM4385)

  (2) Ernst Charge Receptacle 124 (ERNM3001)

  (1) HydriMax

 3600mAh NiMH battery 

(HCAM6333) for receiver

  (1) HydriMax 1600mAh NiMH battery 

(HCAM6308) for engine ignition

Note:

 The length and quantity of servo extensions and 

Y-connectors may vary depending on the brand of radio 

you are using and the radio installation.

RETRACTABLE LANDING GEAR

The Top Flite Giant Fw 190A-3 ARF has been designed 

for Robart pneumatic and electric main gear retracts 
and mechanical tail gear. The tail gear on the full size 
Fw 190A-3 did not retract fully into the fuselage. To 
obtain the scale retraction of the tail gear, a mechanical 
retract was used. Following is the complete list of items 
required to install the Robart retracts:

  (1) Robart TFFW190 Top Flite Giant Fw 190 

pneumatic retractable main landing gear 

(ROBQ1658)

  (1) Robart TFFW190E Top Flite Giant Fw 

190 electric retractable main landing gear 

(ROBQ1657)

  (1) Robart #160 retractable tail gear assembly 

(ROBQ2220)

  (1) Robart #157VRX Large-Scale Deluxe 

Air Control Kit – includes pressure tank, air 

line tubing, variable-rate air valve, T-fi ttings 

(ROBQ2305)

  (1) Robart #169 10' [3048mm] red & purple 

Pressure tubing (ROBQ2369)

  (1 pkg.) #190 Air Line Quick Disconnects 

(ROBQ2395)

Note:

 An air pump will also be required to pressurize 

the air tank. The Robart hand pump could be used, but 
is not practical because of the large capacity of the 
air tank in this model. A small, 12V electric pump is 
recommended and can be purchased at any automotive 
or hardware store.

ADDITIONAL ITEMS REQUIRED

REQUIRED HARDWARE & ACCESSORIES

In addition to the items listed in the

 “

Decisions You 

Must Make”

 

section, following is the list of hardware 

and accessories required to fi nish the Top Flite Giant FW 

190A-3 ARF. Order numbers are provided in parentheses. 

  (2) Dubro #813 1/8" Fuel Line Barb 

(DUBQ0670)

  (1) Dubro #554 X-large Tygon Fuel Line 

(DUBQ0427)

  (1) R/C foam rubber (1/4" [6mm] (HCAQ1000) 

or 1/2" [13mm] (HCAQ1050)

  Propeller and spare propellers suitable for your 

engine.

  (1) Painted Pilot (We used the 1/5 scale 

German Pilot from 

Aces of Iron Productions

)

  (1) 7/64" – 10" [254mm] long Ball-end Hex 

Wrench

OR

  (1) 7/64" Ball-end Hex Wrench (GPMR8003) 

plus (1) 5/32" 

 .014 Round Brass Tube K&S 

#128 (K+SR2628) (See Page 35)

ADHESIVES AND BUILDING SUPPLIES

This is the list of Adhesives and Building Supplies that 

are required to fi nish the Giant FW 190A-3 ARF. 

  1/2 oz. [15g] Thin Pro

 CA (GPMR6001)

  1/2 oz. [15g] Medium Pro CA+ (GPMR6007)

  Pro 30-minute epoxy (GPMR6047)

  Pro 6-minute epoxy (GPMR6045)

Summary of Contents for FW 190





































Reviews: