Top Flite FW 190 Instruction Manual Download | Manualshive

Page: 22 / 36

background image

22

❏

8. Connect a T-fi tting to the air line and to the control

valve. Connect a third air line to the T-fi tting, routing it
out the air tank tray. Install the fi ll valve to the third air

line and install the fi ll valve in the air tank tray.

❏

9. Connect an 8" [203mm] long red and purple air

line to the air control valve. Install quick connects on

the other end of the two air lines. Important: Check
the wing as to which quick connect to install on which
color air line.

❏

10. A method used to mount servo wires and air line

tubing to a structure is to cut a strip of rubber band.
Position the rubber band over the wires and glue the
ends of it to the structure.

Fw 190 FACT

The Fw 190A-3 came with two 7.92mm MG 17
machine guns in the cowl, two 20mm MG 151/20E
cannons in the root of the wing and two 20mm
MG FF cannons in the outer wing panels.

INSTALL THE COWL

❏

1. Using a sanding bar or block with coarse sand

paper, sand a bevel around the edge of the plywood
fan ring. When properly sanded the ring should hold the
plastic fan tight against the front of the cowl.

❏

2. Use sand paper to roughen the back of the outer

ring of the plastic fan. Clean the sanded area with a
paper towel dampened with denatured alcohol.

«
...
20
21
22
23
24
...
»

Summary of Contents for FW 190





































Reviews:

No comments

Related manuals for FW 190

Running worker with wheelbarrow

Brand: Opitec Pages: 5

Brand: THINK GIZMOS Pages: 25

Brand: LEGO Pages: 84

Grange Farm Tipper Wagon

Brand: Bole Laser Craft Pages: 6

Brand: QABA Pages: 8

Thunderbolt Mini A10

Brand: J-Power Pages: 31

Piper Turbo Arrow IV

Brand: 3D AEROWORKS Pages: 28

EF 2000 Single Seater exterior

Brand: Eduard Pages: 3

Toot-Toot Friends Go Pony

Brand: VTech Pages: 9

Baby Annabell 707210

Brand: Zapf Creation Pages: 54

Brand: Fisher-Price Pages: 8

Brand: Phoenix Model Pages: 3

Brand: Wings Maker Pages: 12

Brand: Kibri Pages: 3

Carry & Go Track Table 21802

Brand: Simplay3 Pages: 2

Brand: Eduard Pages: 4

Brand: MINICRAFT Pages: 6

Techno GearsDizzy Droid

Brand: The Learning Journey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands