manualshive.com logo in svg

Top Flite FW 190, Instruction Manual

Share
Download
Top Flite FW 190 Instruction Manual Download Page 27

27

APPLY THE  DECALS

❏

 1. The decals are die-cut from the factory.

❏

 2. Be certain the model is clean and free from oily 

fi ngerprints and dust. Prepare a dishpan or small bucket 
with a mixture of liquid dish soap and warm water—about 

1/2 teaspoon of soap per gallon of water. Submerse 

one of the decals in the solution and peel off the paper 
backing. 

Note:

 Even though the decals have a “sticky-

back” and are not the water transfer type, submersing 
them in soap & water allows accurate positioning and 
reduces air bubbles underneath.

❏

 3. Position decal on the model where desired. Holding 

the decal down, use a paper towel to wipe most of the 
water away.

❏

 4. Use a piece of soft balsa or something similar to 

squeegee remaining water from under the decal. Apply 
the rest of the decals the same way.

Please use the following pictures and the box top as a 
guide for the decal placement.

Summary of Contents for FW 190





































Reviews:

No comments

Brands by name

Popular brands

Load more brands