manualshive.com logo in svg

Top Flite FW 190, Instruction Manual

Share
Download
Top Flite FW 190 Instruction Manual Download Page 21

21

INSTALL THE AIR RETRACT 

CONTROLS

❏

 1. Use epoxy to 

glue the two 5/16" x 

1-3/4" [ 8mm x 44mm] 

hardwood rails to the 
fuel tank former and 
servo tray former. 
Use the embossed 
marks on the servo 
tray former to locate 
the aft hardwood rail. 

The forward hardwood 

rail should be aligned 
with the bottom of the 
opening in the fuel 
tank former.

❏

 2. Glue the retract servo tray together as shown.

❏

 3. Test fi t the retract servo tray in the fuselage. It 

should fi t between the two hardwood rails. Drill a 1/16" 
[1.6mm] pilot hole in the hardwood rails using the four 
mounting holes as guides. Attach the retract servo tray 
to the rails with #2 x 3/8" [9.5mm] sheet metal screws 
and #2 washers. Remove the screws and the tray and 
harden the screw holes with thin CA.

❏

 4. Install the retract control valve in the plywood 

mount. Install a .080 ball link ball and .080 nut on the 
valve. Be sure to use a drop of threadlocker on the 
threads of the ball link ball. 

❏

 5. Install the retract control valve servo in the retract 

servo tray and plug it into the receiver.

❏

 6. Cut off 1/2" [13 mm] from the threaded end of the 

2-56 x 4" [102 mm] metal pushrod. Thread the nylon 
ball socket on the pushrod. Snap the ball socket onto 
the ball link ball on the retract control valve. Center the 
servo arm and mark the pushrod where it crosses the 
servo arm. Make a 90 degree bend at the mark. Install 
the pushrod in the servo arm and install a nylon Faslink. 
Cut the pushrod 1/8" [3mm] past the Faslink. Reinstall 
the retract servo tray in the fuselage with the #2 x 3/8" 
[9.5mm] sheet metal screws and #2 washers.

❏

 7. Install a length of air line on the pressure tank. 

Secure the pressure tank in the cradle with a rubber 

band. To prevent the tank from sliding, a couple of dabs 
of silicone adhesive can be applied to the cradle.

Summary of Contents for FW 190





































Reviews:

No comments

Brands by name

Popular brands

Load more brands