manualshive.com logo in svg

Top Flite FW 190, Instruction Manual

Share
Download
Top Flite FW 190 Instruction Manual Download Page 14

14

INSTALL THE ELEVATOR & RUDDER SERVOS

❏

 1. Insert the three 4-40 x 48" [1220mm] metal 

pushrods in the elevator and rudder pushrod outer 
pushrod tubes at the aft end of the fuselage. Install two 
elevator and one rudder servo in the servo tray as shown.

❏

 2. Thread a 4-40 nut, threaded clevis and a silicone 

clevis retainer onto both elevator pushrods and the 
rudder pushrod.

❏

 3. Mount the control horns to the elevators and 

the rudder following the same procedure used on the 
ailerons, by drilling 3/32" [2.4mm] pilot holes and using 

#4 x 1/2" [13mm] sheet metal screws for the rudder 

control horn and the 

front

 screws in the elevator horns. 

IMPORTANT:

 Use #4 x 3/8" [9.5mm] sheet metal 

screws for the aft screws in the elevator control horn. 
Don’t forget to harden the holes with thin CA after fi rst 
installing, then removing the screws.

❏

 4. Connect the receiver battery, rudder and elevator 

servos to the receiver. Switch on the transmitter and 
center the servos. Install a single arm servo on each 
servo, perpendicular to the centerline of the servo. 

To obtain the required amount of rudder throw, a 3/4" 

[19 mm] servo arm was installed on the rudder servo. 

❏

 5. Install solder clevises on the elevator servo arms in 

the hole 7/16" [11mm] from the center of the servo arm. 

Install a solder clevis on the rudder servo arm in the hole 
3/4" [19mm] from the center of the servo arm. Follow 
the same procedure that was used for the aileron and 
fl ap pushrods. Mark the elevator and rudder pushrods 
where they are to be cut for the solder clevises. One at a 
time, remove the threaded metal clevis from the control 
horn end, remove the pushrod from the fuselage, cut it 
to the correct length and solder a metal solder clevis on 
the end. Reinstall the pushrod inside the fuselage and 
connect the solder clevis to the servo arms. Reinstall 
the threaded metal clevis and 4-40 nut. 

Don’t forget 

to use a silicone clevis retainer on all the clevises. 

MOUNT THE RETRACTABLE TAIL GEAR

❏

 1. Remove the steering arm 

from the Robart #160 retractable 
tail gear assembly (not included). 
File a fl at spot near the top of 
the shaft for the set screw in the 
steering arm to lock onto. File a 
second fl at spot near the bottom 
of the shaft for the set screw in 
the strut. Mount the strut on the 
shaft with a drop of threadlocker 
on the set screw.

❏

 2. Install the compression spring, included with the 

Fw 190, on the shaft, between the strut and the tail 
gear frame. Compress the spring while tightening the 
set screw in the steering arm.

Summary of Contents for FW 190





































Reviews:

No comments

Brands by name

Popular brands

Load more brands