manualshive.com logo in svg

Top Flite FW 190, Instruction Manual

Share
Download
Top Flite FW 190 Instruction Manual Download Page 25

25

❏

 6. To install the instrument panel, fi rst, insert the 

bottom of the panel face down. Apply glue to the back 
of the panel, then rotate the panel into position.

❏

 7. Trim the edges of the canopy deck so that it fi ts 

fl ush with the sides of the fuselage. Glue the canopy 
deck to the fuselage.

❏

 8. Center and glue the armor plate to the back of 

the cockpit.

❏

 9. Sand the bottom center of the seat and the top 

of the seat pedestal. Clean the area with denatured 
alcohol and glue the seat to the pedestal.

❏

 10. If you are installing a full body pilot, now is a good 

time to install him before the control stick is installed. 
Cut the control stick to the appropriate length using the 

height of the seat as a guide. Glue the control stick in 
the control stick boot.

❏

 11. Apply the “Attention” decal to the armor plate.

❏

 12. Install the pilot bust in the cockpit. You will need 

to use a block to raise the pilot.

❏

 13. Wash the canopy in warm water. Then, dry it 

off. Place the canopy on the fuselage. Be certain it is 
centered from side-to-side and mark the outline on the 

Summary of Contents for FW 190





































Reviews:

No comments

Brands by name

Popular brands

Load more brands