manualshive.com logo in svg

Top Flite FW 190, Instruction Manual

Share
Download
Top Flite FW 190 Instruction Manual Download Page 5

5

❍

  Threadlocker thread locking cement 

(GPMR6060)

❍

  Mixing sticks (50) (GPMR8055)

❍

  Mixing cups (50) (GPMR8056)

❍

  Epoxy brushes (6) (GPMR8060)

❍

  Denatured alcohol (for epoxy clean up)

❍

  R/C-56 canopy glue (JOZR5007)

❍

  Milled fi berglass (GPMR6165)

❍

  Masking tape

❍

  Plan protector (GPMR6167) or wax paper

❍

  Drill

❍

  Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32" 

[2.4mm], 1/8" [3.2mm], 3/16" [4.8mm], 13/64" 
[5.2mm], 1/4" [6.4mm]

❍

  Small metal fi le

❍

  Stick-on segmented lead weights (GPMQ4485)

❍

  Silver solder w/fl ux (STAR2000)

❍

  Hobby Heat

™

 Micro Torch II (HCAR0755)

❍

 #1 Hobby knife (RMXR6903)

❍

 #11 blades (5-pack, RMXR6930)

❍

  Curved-tip canopy scissors for trimming plastic 

parts (HCAR0667)

COVERING TOOLS

❍

  Top Flite MonoKote

®

 sealing iron (TOPR2100)

❍

  Top Flite Hot Sock

™

 iron cover (TOPR2175)

❍

  Top Flite MonoKote trim seal iron (TOPR2200)

❍

  Top Flite MonoKote heat gun (TOPR2000)

OPTIONAL SUPPLIES AND TOOLS

Here is a list of optional tools mentioned in the manual 
that will help you build the Giant FW 190A-3 ARF.

❍

  2 oz. [57g] spray CA activator (GPMR6035)

❍

  CA applicator tips (HCAR3780)

❍

  CA debonder (GPMR6039)

❍

  Builder’s Triangle Set (HCAR0480)

❍

  Scale Warbird Template (TOPR2187)

❍

  36" metal ruler (HCAR0475)

❍

  Hobbico

®

 High Precision Diagonal Cutter 5" 

(HCAR0630)

❍

  Pliers with wire cutter (HCAR0625)

❍

  Robart Super Stand II (ROBP1402)

❍

  Switch & Charge Jack Mounting Set 

(GPMM1000)

❍

  Panel Line Pen (TOPQ2510)

❍

  Rotary tool such as Dremel

❍

  Rotary tool reinforced cut-off wheel 

(GPMR8200)

❍

  Servo horn drill (HCAR0698)

❍

  AccuThrow

™

 Defl ection Gauge (GPMR2405)

❍

  CG Machine™ (GPMR2400)

❍

  Precision Magnetic Prop Balancer (TOPQ5700)

IMPORTANT BUILDING NOTES

●

   Anytime a sheet metal screw is installed in wood, 

fi rst install the screw, remove the screw and apply a 
couple of drops of thin CA in the hole to harden the 
threads. After the CA has cured, reinstall the screw.

●

   

Photos

 and 

sketches

 are placed 

before

 the step 

they refer to. Frequently you can study photos in 
following steps to get another view of the same parts.

●

   The Giant FW 190A-3 ARF is factory-covered with Top 

Flite MonoKote fi lm. Should repairs ever be required, 
MonoKote can be patched with additional MonoKote 

purchased separately. MonoKote is packaged in six-
foot rolls, but some hobby shops also sell it by the 
foot. If only a small piece of MonoKote is needed 
for a minor patch, perhaps a fellow modeler would 
give you some. MonoKote is applied with a model 
airplane covering iron, but in an emergency a regular 
iron could be used. A roll of MonoKote includes full 
instructions for application. Following are the colors 
used on this model and order numbers for six foot rolls.

White (TOPQ0204)
CubYellow (TOPQ0220)
Flat Black (TOPQ0508)
Flat Olive Drab (TOPQ0510)
Flat Dove Gray (TOPQ0511)

●

   The stabilizer and wing incidences and engine 

thrust angles have been factory-built into this model. 
However, some technically-minded modelers may 
wish to check these measurements anyway. To view 
this information visit the web site at www.top-fl ite.com 

and click on “Technical Data.” Due to manufacturing 
tolerances which will have little or no effect on the way 
your model will fl y, please expect slight deviations 
between your model and the published values.

MODEL INSPECTION

Before starting to build, take an inventory of this model 
to make sure it is complete, and inspect the parts 
to make sure they are of acceptable quality. If any 
parts are missing or are not of acceptable quality, or if 
you need assistance with assembly, contact 

Product 

Support

. When reporting defective or missing parts, 

use the part names exactly as they are written in the 
instruction manual.

Top Flite Product Support

3002 N Apollo Drive, Suite 1
Champaign, IL 61822

Ph: (217) 398-8970, ext. 5     Fax: (217) 398-7721

E-mail: productsupport@top-fl ite.com

ORDERING REPLACEMENT PARTS

Replacement parts for the Top Flite Giant FW 190A-
3 ARF are available using the order numbers in the 

Replacement Parts List

 that follows. The fastest, most 

economical service can be provided by your hobby 
dealer or mail-order company. Not all parts are available 
separately (an aileron cannot be purchased separately, 
but is only available with the wing kit). Replacement 
parts are not available from Product Support, but can 
be purchased from hobby shops or mail order/Internet 
order fi rms. Hardware items (screws, nuts, bolts) are 
also available from these outlets.

To locate a hobby dealer, visit www.top-fl ite.com and 

click on “Where to Buy”. Follow the instructions provided 
on the page to locate a U.S., Canadian or International 
dealer.

Parts may also be ordered directly from Hobby Services 

by calling (217) 398-0007, or via facsimile at (217) 398-

7721, but full retail prices and shipping and handling 

charges will apply. Illinois and Nevada residents will also 
be charged sales tax. If ordering via fax, include a Visa

®

 

or MasterCard

®

 number and expiration date for payment.

Summary of Contents for FW 190





































Reviews:

No comments

Brands by name

Popular brands

Load more brands