manualshive.com logo in svg

Toho Electronics TTM-P4W Series, Instruction Manual, Page: 23 / 25

Share
Download
Toho Electronics TTM-P4W Series Instruction Manual Download Page 23

 

22 

8. Specifications and Rating 

 

 

8.1 General specifications 

 

Storage cell 

Each setting value is stored in EEPROM. 

Power supply voltage 

100 to 240 VAC ±10%, 50/60Hz (free power supply) 

Power consumption 

10 VA or less 

Insulation resistance 

Measuring terminal – case: 500 VDC, 20 M

 

Power supply terminal – case: 500 VDC, 20 M

 

Withstand voltage 

Measuring terminal – case: 1000 VAC for 1 minute 
Power supply terminal – case: 1500 VAC for 1 minute 

Operating 
environment 

Ambient 
temperature 

0 to 50°C 

Ambient 
humidity 

20 to 90%RH (no condensation) 

Storage 
environment 

Ambient 
temperature 

-25 to +70°C (no freezing and condensation) 

Ambient 
humidity 

5 to 95%RH (no condensation) 

Weight 

180 g or less 

Installation environment 

-  No corrosive gas, dust, and oil 
-  Place far from the source of electric noise and less affected by the 

electro- magnetic field 

-  No mechanical vibration and shock 
-  No direct sunlight 
-  Indoor 
-  Max. 2,000 m above sea level 
-  2 or less of pollution degree  

Installation 

Installation category II 

Control type 

PID or ON/OFF 

 
 

Summary of Contents for TTM-P4W Series


























Reviews:

No comments