Toa VX-3308WM Operating Instructions Manual Download Page 73

Page: 73 / 89

Chapter 3

OPERATION

Step 3.

When making broadcast using the RM-200SF, follow

the procedures below.

• Press the All-Zone Call key (4) to select all zones.

In this event, the Selection indicator lights.

Zone monitor indicator

Selection indicator

All-Zone Call key

Green

• Press the Talk key (5), then make voice

announcements to all zones.

In this event, the Broadcast status indicator lights

yellow, and the Microphone indicator lights green.

Talk key

Broadcast Status Indicator

Microphone Indicator

Yellow

Green

Also, the Zone monitor indicator of the All-Zone Call

key (4) lights yellow.

Zone monitor indicator

Selection indicator

All-Zone Call key

Tip

Yellow

Green

When a Fireman's Microphone announcement interrupts a message broadcast, the broadcast mode

that follows Fireman's Microphone announcement completion can be set to either "Continue" for

continuous EV message broadcast or "Silent" for broadcast termination. This setting can be made by

using the VX-3000 Setting Software.

Step 4.

Terminate the Emergency status.

Press the Emergency Reset key (3).

The restoration message is broadcast to the entire zone, and the

Restoration EV message status indicator of the Emergency Reset

key (3) lights while the message is broadcast.

After the message broadcast completion, the VX-3000 system

is restored from Emergency status to the General-purpose

broadcast status, and the Emergency status indicator (1) built in

the Emergency key goes off.

Emergency key

Goes off

Restoration EV message

status indicator

Green

Emergency Reset key

Summary of Contents for VX-3308WM


























































































Search results

Summary of Contents for VX-3308WM

Reviews:

Brands by name

Popular brands

Toa VX-3308WM, Operating Instructions Manual

Search results

Summary of Contents for VX-3308WM

Reviews:

Brands by name

Popular brands