Toa VX-3308WM Operating Instructions Manual Download Page 69

Page: 69 / 89

3-10

Chapter 3

OPERATION

3. EMERGENCY BROAdCAST

3.1. Typical System Examples

Here, an example of sequential operation with the VX-3000 system is explained.

[Sequential Operation]

Sequential operation consists of Phase 1 and Phase 2.

Sequence Phase 1 operates upon emergency system activation. When the set time interval elapses, the

broadcast is automatically switched to Phase 2.

[Setting Contents]

Both the broadcast messages and output zones are set for Phase 1 and Phase 2.

Assuming that these phases are set as follows:

Phase 1: The alert message is continuously broadcast for 5 minutes to each floor of each building.
Phase 2: The evacuation message is continuously broadcast to the entire zone.

[Alert and Evacuation Message Examples]

Alert Message:

The fire alarm system has been engaged. We are now checking the cause.

Please wait for further information.

Evacuation Message: There is a fire. Please evacuate immediately.

General-purpose

broadcast mode

Emergency

sequence

Phase 1

5 minutes

BGM

Building A

Building B

BGM

Building A

Building B

BGM

Alert

Emergency activation signal

Step 1. Background music (BGM) is

broadcast to A-GF (Building A

ground floor) and B-GF (Building B

ground floor) when the system is in

general-purpose broadcast mode.

Step 2. The sensor installed on A-3F

detects irregularities, and the fire

alarm system transmits a control

signal to the control input.

The emergency mode is activated,

allowing the alert message to be

played through to A-3F.

Summary of Contents for VX-3308WM


























































































Search results

Summary of Contents for VX-3308WM

Reviews:

Brands by name

Popular brands

Toa VX-3308WM, Operating Instructions Manual

Search results

Summary of Contents for VX-3308WM

Reviews:

Brands by name

Popular brands