manualshive.com logo in svg

TIPTEL easyDECT XL2, Operating Instructions Manual

Share
Download
TIPTEL easyDECT XL2 Operating Instructions Manual Download Page 66

 Favorite (special functions)

64

must be set to DTMF dialing mode. Lift the handset and dial the call number.

Base station and handset of easyDECT XL 2 ring once and the telephone ties up

the line. Then enter the four-digit access code.

The handset of easyDECT XL 2 switches to listening mode and you can hear what

is happening in the room. If you prefer ”silent monitoring” without the single ring,

you should deactivate the ringing tone on the base station and the handset (see

Page 39).

• Make sure that you observe data protection laws when using ”silent

monitoring”.

• Before you turn on the ”Room monitoring” function, the access code must

be programmed (see paragraph below)

Changing the access code for room monitoring

The 4-digit access code for room monitoring is not preset and must be entered by

the user. You can change your access code at a later date if necessary. Entering

the code initially and any subsequent changes use the following procedure:

1. Press the MENU soft key to display the main menu items.
2. Press the arrow keys to choose „Favorite“, then press SELECT soft

key.

3. Press the arrow keys to choose „2:Room Monitor“, then press the

SELECT soft key.

4. Enter the current base PIN and press the OK soft key.
5. Press the arrow keys to choose „2:Monitor Code“, then press the

OK soft key.

6. Enter the Monitor Code (4 digits) using the number key and press

the OK soft key. (The code 0000 is not permitted and will not be

accepted!).

7. Press the 

 key to exit.

Summary of Contents for easyDECT XL2






















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands