21
Storage
Before storage unload and remove air supply (see page 13). Then install
Barrel Sleeve (see page 2) and put your marker in Safe Mode (see page 4).
You should store your marker in a dry area. Before storing your marker
make sure that the marker is cleaned and oiled (see cleaning and
maintenance on page 13) so that it does not rust. Store your marker with
the bolt in the forward position
, uncocked.
When removing your marker out of storage make sure Barrel Sleeve is
installed (see page 2) and safety is in Safe Mode (see page 4). You should
oil the rear bolt and the front bolt o-ring if needed before use.
Repairing Air Supply Cylinder Leaks
The most common leak occurs from a bad air supply valve o-ring. To replace
a valve o-ring you must first remove the bad o-ring and then install a new
one. This o-ring is located on the tip of your air supply valve. The best valve
o-rings are made of urethane. The urethane o-rings are not affected by high
air supply pressures. These may be purchased from Tippmann
®
or your
local paintball dealer. NOTE: If new valve o-ring does not resolve air supply
leak, do not attempt to repair air supply cylinder. Contact Tippmann Sports,
LLC or your local paintball dealer.
❏
Install Receiver Cover
: Spread and slide the cover into place until
Front Grip Cover guides align with guides on Receiver and cover fits flush.
Start 2 screws
/
(one on each side) and tighten.
❏
Install Front Grip cover
(or Front Grip
on models XT or eXT): Slide
it into position, start round head bolt
and tighten.
❏
Install Barrel
: Oil the barrel o-ring and insert the barrel into the receiver
and turn clockwise until snug.
❏
Install the Hopper and
❏
adjust the velocity (see instructions on page 7).
Bolt = 1 1/16”
Bolt = 7/8”
Bolt = 5/8”
Bolt = 1/2” Flat Head
Bolt = 1/2” Round Head
Screw = 1/2” +Head
20
E
N
G
L
I
S
H
Assembly (continued from page 20)
E
N
G
L
I
S
H
Receiver Assembly (continued on page 21)
Assembly (continued from page 19)
TO ASSEMBLE THE MID-GRIP HALVES ONTO THE RECEIVER
:
❏
1) Make sure square nut
is in place in right Mid-Grip half
.
❏
2) Place top of right Mid-grip half
onto right side of receiver and align
bottom to fit flush onto Tank Adapter lug/pin
.
❏
3) Guide top of left Mid-Grip half onto left side of receiver so the gas line
fits inside and the bottom fits onto adapter lug-pin
and it aligns flush onto
Right Mid-Grip half
.
❏
Insert and tighten 4 screws
.
❏
4) Insert and tighten 2 bolts
/
. Mid-Grip installation is complete.
❏
3) Install Battery Cover
: with Grip-Frame
attached to receiver
❏
insert Battery Cover into position,
❏
insert Battery Cover Bolt
and tighten. Grip Frame installation is complete.
TO INSERT AND ATTACH THE GRIP FRAME
TO THE RECEIVER and THE TANK ADAPTER:
❏
1) Insert the front end of the Grip Frame
into the
receiver and align it to fit onto the lug
, then carefully
tilt it side to side as you work it up into place until it fits
flush on the receiver.
❏
Insert bolt
through back of grip frame, into
receiver and tighten.
❏
Insert bottom of trigger guard
into grip frame,
and
❏
position top of trigger guard so you can insert
bolt
through it into the receiver and tighten.
❏
2) Align Tank Adapter
to Grip Frame,
❏
insert
2 tank adapter bolts
and tighten.
