Thunder Laser NOVA-24 User Manual Download Page 77

Page: 77 / 77

THUNDER LASER

NOVA-35

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

5.6 Maintenance Plan

DAILY CHECK LIST

①

Check Mirrors and lens for condensation and make sure it is clean after work

②

Check exhaust grille to ensure there is no blockage for exhaust fan

③

Check coolant water level

④

Check air filter on compressor

⑤

Ensure cooling fans on sides are free from debris

⑥

The air blower must be checking and cleaning if required.

WEEKLY CHECK LIST

①

Clean filters on water chiller

②

Clean debris from under laser bed

③

Clean X & Y & Z axis rails and lubricate as required

④

Clean Acrylic/Tempered glass covers in lid

⑤

The beam combiner must be checking every weekly, and cleaning if required.

THE END

Summary of Contents for NOVA-24














































































Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands

Thunder Laser NOVA-24, User Manual

Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands