Thunder Laser NOVA-24 User Manual Download Page 13

Page: 13 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

concentration must not be exceeded.)

3. PVC (polyvinyl chloride) must under no circumstances be processed

with the laser.

Should you have further questions before starting work, please feel free to write us

an email at:

[email protected]

2.4 Warning and Information Labels

The warning and information labels are attached in such positions of

the device that could represent a source of danger during set-up and

operation. Therefore, follow the information on the labels. If labels are

lost or damaged, they must be replaced immediately.

Summary of Contents for NOVA-24














































































Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands

Thunder Laser NOVA-24, User Manual

Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands