manualshive.com logo in svg

Thunder Laser NOVA-24, User Manual

The Thunder Laser NOVA-24 is a cutting-edge laser engraving machine, designed to deliver impeccable precision and efficiency. Unlock its full potential with the comprehensive User Manual, available for free download from our website. This essential manual guarantees a seamless user experience and provides valuable insights into maximizing your creativity.

Share
Download
background image

THUNDER LASER

                                  

NOVA-24

 

 

www.thunderlaser.com

                              

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

 

[email protected] 

      Shatian Town, Shatian Dadao, Mintian

 

Tel :(86)769 826653                             

Dongguan City, Guangdong Province, China

 

23       

3.8    Connections 

    Perform the connections exactly in the order described; otherwise 

electrostatic charging can damage your computer and/or the electronics 

of the laser system. 

3.8.1 

Connecting the Mains 

Connect one end of the mains cable with the connection socket at the rear side of the 

laser device (see Figure below) and the other end with a protected power outlet. 

 

 

Mains voltage  and operating voltage must correspond (AC 230V  50/60  Hz or AC 115V 

50/60 Hz) – see information label beside the connection socket.   

    Under no circumstances switch on the device if the voltages do not 

correspond. 

 

 

 

Summary of Contents for NOVA-24














































































Reviews:

No comments

Related manuals for NOVA-24

Vision Phoenix 1212 S5 User Manual preview
Phoenix 1212 S5
Brand: Vision Pages: 148

Brands by name

Popular brands

Load more brands