Thunder Laser NOVA-24 User Manual Download Page 22

Page: 22 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

3.7 Computer – Requirements

The following recommendation represents the minimum requirements. When using a

more powerful computer the graphics are generated and displayed faster and the

computing times and the data transfer to the laser are reduced. To use the newest

software version, you might have to abide other requirements.

•

Windows 10 (32 bit or 64 bit )

•

Windows 8 (32 bit or 64 bit )

•

Windows 7 (32 bit or 64 bit )

Windows Vista (with Service Pack 1 or later)

Windows XP (with Service Pack 2 or later)

•

1024 MB of RAM, 400 MB of hard disk space

•

Pentium® 3 or 4 processor or AMD Athlon™ XP

•

1024 x 768 or better monitor resolution

•

1 free USB interface

•

1 free Ethernet interface

•

Mouse

Summary of Contents for NOVA-24














































































Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands

Thunder Laser NOVA-24, User Manual

Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands