Thunder Laser NOVA-24 User Manual Download Page 31

Page: 31 / 77

THUNDER LASER

NOVA-24

www.thunderlaser.com

DONGGUAN THUNDER LASER EQUIPMENT CO.,LTD

[email protected]

Shatian Town, Shatian Dadao, Mintian

Tel :(86)769 826653

Dongguan City, Guangdong Province, China

1. Top lid 16. Laser power switch

2. Hand valve Pneumatic Fitting 17. Main power switch

3. Auto focus sensor 18. Ethernet port

4. Left-up side door 19. U-disk connection port(USB)

5. Left side door 20. PC connection port(USB)

6. X-axis 21. Right side door

7. Laser heads 22. Right-up side door

8. Front door 23. Indicate light

9. Honey comb table 24. Power supply socket

10. Y-axis 25. Laser tube cover

11.

Front up door

26. Exhaust hose

12. Flap protection sensor 27. Blow air port

13. Control panel 28. Water in and water out

14. Emergency stop switch 29. Manufacturer’s label

15. LED lamp

1. Top lid

If the Top lid is opened, no data is processed. When the protection cover is opened

during working, the motion system is stopped and the laser source is turned off.

During processing of commands the protection cover must only be opened after

pressing the “Pause “button.

2. Hand valve Pneumatic Fitting

It’s used for adjust that blow air amount.

3. Auto focus sensor

Used for the automatic focusing of the work table.

4. Left-up side door

Open this door for cleaning the second reflective mirror or align that laser beam

5. Left side door

Summary of Contents for NOVA-24














































































Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands

Thunder Laser NOVA-24, User Manual

Search results

Summary of Contents for NOVA-24

Reviews:

Related manuals for NOVA-24

Brands by name

Popular brands