76
Remote Control Layout
1. POWER.
After the rear panel
MAIN POWER
switch
is turned on, press this button to exit the standby
mode. Pressing
POWER
again will place the
Casablanca II into standby mode, thereby turning off
the VFD (or LCD) and muting all outputs.
2. REMOTE.
Activates/deactivates the
REMOTE
POWER
jack(s) on the rear panel that are assigned
to this button.
3. MUTE.
Mutes all analog audio outputs except the
TAPE OUT
jacks. Press again to disable muting.
4. STATUS.
Displays the current status of the
Casablanca II in the VFD (or LCD) and on the video
monitor if optional video card is installed and video
display is enabled.
5. INPUTS.
Individual buttons which select the desired
input channel. Within a function’s sub menu page(s),
these buttons select sub functions to edit. When
pressed, they activate a corresponding LED on the
front panel and an arrow or sub menu on the video
monitor.
6. A-D.
Sequences through input jacks assigned
(mapped) to the active
INPUT SELECT
button. Also
toggles between some menu pages.
7.
and
-.
Incrementally changes the
INPUT
channel, thereby taking the place of buttons
1
to
6
.
8. LEVELS UP
and
DOWN.
Adjusts master volume for
all speaker outputs. Also increments/decrements
parameter values in most edit modes and shifts
FRONT
/
REAR
audio in the first
BALANCE
menu.
9. LEVELS LEFT
and
RIGHT.
Shifts the audio balance
to the left or right in the first
BALANCE
page. Also
used to adjust the
MASTER
volume level when in
most sub menus.
10. DISPLAY.
Temporarily overrides the VFD (or LCD)
brightness display setting in the
SETUP
/
INPUT
page 1
submenu.
11. PHASE.
Inverts the phase (180
°
) of all speaker
outputs.
Figure 65 - Remote Control Layout
12. MODE.
Activates/deactivates the
MODE
select pages for currently selected input.
13. TAPE OUT.
Used for routing both audio and video signals to their respective
TAPE OUT
jacks.
14. BALANCE.
Activates the
BALANCE
menus in order to set a temporary balance configuration to adjust for different
program characteristics.
15. SETUP.
Displays multiple pages of sub menus which provides access for setting speaker
configurations/levels/delays, analog input levels, naming inputs, setting the display & remote features, selecting the
video type, setting options for incoming Dolby Digital, DTS and Circle Surround signals and much more.
Note
: When operating the hand held remote control, point it at the remote sensor on the Casablanca II’s front panel.
The remote control can be used from 3 to 20 feet from the Casablanca II and within a 30
o
angle from each side of the
sensor. Exposing the the remote sensor to direct sunlight or strong light may cause faulty operation.
Summary of Contents for Casablanca II
