53
AVAILABLE SETTINGS
BUTTON PARAMETER
1
FREQ
40
50
63
80
100 125 160
2
SLOPE
6 12 18 24 - - -
3
LP
φ
- +
Figure 26 - Front Panel Display of the Front left/Right Speaker Configuration
Submenu
Pressing button #
1
allows the configuration of the front left/right speakers. If these speakers are not to be crossed
over, nor any of their signal sent to the
SUB
output(s), then this should be set to
FULL
. There is an option where the
full range signal can be routed to the left/right speakers and a low pass part of it routed to the sub. If this is desired, the
setting should be
FUL/LP
. (A crossover type must be selected (button #
5
), and the appropriate crossover frequencies
and slopes set up.) The front left/right speakers can also be set to
OFF
.
Note
: If the crossover type is Phase Perfect (
φφφφ
PERF
) and the
CFG
type is set to
FUL/LP
, no low pass signal will be
created.
Should it be desired to fully crossover the front left/right speakers, the
CFG
setting (button #
1
) should be set to
XOVER
and the crossover frequencies and slopes in either the Phase Perfect (
φφφφ
PERF
), Linkwitz-Riley (
LINK-RILEY
) or
Butterworth (
BWORTH
) sub menus be set using buttons
2
,
3
and/or
4
respectively.
Note
: It is advisable to select the same crossover frequencies and slopes in all 3 crossover type sub menus (buttons
2
-
4
), and then select the crossover
TYPE
(button #
5
) and audition each crossover. Initially, this should be done with all
other speakers turned off. This procedure should be applied when configuring each speaker set.
Set up the crossovers as follows. Press button #
2
(
φφφφ
PERF
). This submenu is shown in figure 27.
Figure 27 - Front Panel Display of the SETUP
/
INP
/
CONFIG
/
LT/RT/
φφφφ
PERF Sub Menu
Press button #
1
and select a Phase Perfect crossover frequency for the front left/right speakers, then button #
2
to set
the high pass slope.
Button #
3
allows the user to invert the low pass phase from 0 (
+
) to 180 degrees out of phase .
Table 2 - Available configuration settings for front L/R speaker Phase Perfect crossover.
Press
SETUP
once to return to the front left/right configuration sub menu, then press button #
3
(
LINK-RILEY
) to set
up the Linkwitz-Riley crossovers. This submenu is shown in figure 28.
Summary of Contents for Casablanca II
