Thermo Scientific Orion 310 Instruction Manual Download | Manualshive

Page: 21 / 81

background image

17

PerpHecT

®

Orion 310, 320, 330 Instruction Manual

B. Orion 310 Temperature Calibration Procedure

This procedure should be performed at least once per week to ensure
accurate temperature compensation when operating in the LogR mode.
If the meter is powered down or the electrode disconnected, it is
recommended that you recalibrate the LogR temperature. See the
Appendix Section for accuracy specifications and recommended
calibration techniques.

Choose a temperature calibration range which is at least 5

°

C apart

depending on your expected operating range. Evenly bracket your
expected sample temperature range. A maximum 20

°

C range is

recommended for maximum accuracy. For example, for measurement
around 20

°

C calibrate at 10

°

C and 30

°

C. For temperature span greater

than 20

°

C, a three-point temperature calibration is recommended.

For many samples, a single-point calibration near the expected sample
temperature will yield adequate results. A constant temperature bath or
a hot plate is recommended to hold the temperature of calibrating solution.

For best results during temperature calibration, it is recommended
that pH buffer or tap water be used as the temperature calibrating solution.

Do Not Use

deionized water because the conductivity is too low to obtain a

good calibration.

IMPORTANT:

When using the meter for the first

time or restarting in the LogR mode, you must
perform a LogR temperature calibration. It is
recommended that at least a two-point temperature
calibration be performed to meet optimum system
accuracy. See Appendix Section for additional
information.

Introduction to Patented digital LogR pH Measurement for Orion 310

«
...
19
20
21
22
23
...
»

Summary of Contents for Orion 310


















































































Reviews:

No comments

Related manuals for Orion 310

Brand: Keithley Pages: 32

Brand: Oldham Pages: 34

Brand: SAGEMCOM Pages: 33

Brand: Percussion Play Pages: 3

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: Hanna Instruments Pages: 28

Brand: UEi Pages: 16

zelsius C5 -IUF

Brand: Zenner Pages: 28

Brand: R&S Pages: 46

Brand: General Pages: 16

Brand: WIKA Pages: 52

Brand: Laguna Tools Pages: 28

Brand: Keison Pages: 56

SeeLeveL II 709-RVC

Brand: Garnet Pages: 35

Brand: HYKKER Pages: 22

Brand: PRAXSYM Pages: 20

Brand: ATIM Pages: 32

Brand: Kobold Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands