Thermo Scientific Orion 310 Instruction Manual Download

Page: 62 / 81

PerpHecT

Orion 310, 320, 330 Instruction Manual

58 Operator Assistance Codes Orion 310, 320 and 330

Code

Description

Causes / Suggestions

E-35

Bad LogR

Displayed when two calibration standards

Standard

do not differ in temperature by the
minimum allowable differences in
LogR mode.

1. The difference between temperature

points must be at least 5

E-36

No LogR Cal

Displayed when the calibration
coefficients from a LogR calibration
are out-of-range. Incorrect temperature
value entered.

1. Recheck temperatures and recalibrate.

2. Check electrode and inputs

E-40

Serial Memory

Displayed at power-up when an error

Error

occurs accessing factory calibration data.

1. Unplug meter, plug in again after

10 seconds.

Summary of Contents for Orion 310


















































































Search results

Summary of Contents for Orion 310

Reviews:

Related manuals for Orion 310

Brands by name

Popular brands

Thermo Scientific Orion 310, Instruction Manual

Search results

Summary of Contents for Orion 310

Reviews:

Related manuals for Orion 310

Brands by name

Popular brands