Thermo Scientific Agilent 1200 Series Getting Connected Manual Download Page 45

Page: 45 / 58

Thermo Scientific

Agilent 1200 Series Getting Connected Guide for LC Devices

Connecting the Communication Cables

This chapter describes how to connect the Agilent 1200 Series LC modules to the data system
computer and how to make the contact closure connection between the LC stack and a
Thermo Scientific mass spectrometer.

Ethernet Communication Kit

To connect the Agilent LC system to a Thermo Scientific mass spectrometer, you must have
the following parts:

• Ethernet Communication Kit (

Table 3

)

• Agilent LAN card, Model G1369, unless the Agilent LC system contains a module with

an on-board LAN communication interface (

Figure 24

)

• Agilent BCD board for contact closure

Contents

•

Ethernet Communication Kit

•

Connecting the Ethernet Cables

•

Connecting the Contact Closure Cable

Table 3.

Ethernet Communication Kit (P/N OPTON 30012)

Description

Part number

Agilent BCD (contact interface) board

00012-27714

Contact closure cable with 15-pin connector

Instead of using the contact closure (trigger) cable, you can use the contact closure cable supplied by Agilent
Technologies Inc. (P/N G1103-61611)

00012-27716

Ethernet cable, straight shielded Cat5, 3 m (10 ft)

00012-70008

Fast Ethernet switch, 10T/100Base-TX, 5-port

00825-01-00024

Summary of Contents for Agilent 1200 Series



























































Search results

Summary of Contents for Agilent 1200 Series

Reviews:

Related manuals for Agilent 1200 Series

Brands by name

Popular brands

Thermo Scientific Agilent 1200 Series, Getting Connected Manual

Search results

Summary of Contents for Agilent 1200 Series

Reviews:

Related manuals for Agilent 1200 Series

Brands by name

Popular brands