Thermo Scientific Agilent 1200 Series Getting Connected Manual Download Page 11

Page: 11 / 58

Preface

Thermo Scientific

Agilent 1200 Series Getting Connected Guide for LC Devices

Contacting Us

There are several ways to contact Thermo Fisher Scientific for the information you need.

For Thermo Scientific™ products

Access by phone, fax, email, or website

Technical Support

(U.S.)

Phone: 1 (800) 532-4752

Fax: 1 (561) 688-8736

Email:

[email protected]

Web—for product support, technical documentation, and knowledge bases:

www.thermoscientific.com/support

Customer Service

(Sales and service)

(U.S.)

Phone: 1 (800) 532-4752

Fax: 1 (561) 688-8731

Email:

[email protected]

Web—for product information:

www.thermoscientific.com/lc-ms

Web—for customizing your service request:

1. From any Products & Services web page, click

Contact Us

2. In the Contact Us box, complete the information requested, scroll to the

bottom, and click

Send

User Documentation

Web—for downloading documents:

mssupport.thermo.com

1. On the Terms and Conditions web page, click

I Agree

2. In the left pane, click

Customer Manuals

3. To locate the document, click

Search

and enter your search criteria. For

Document Type, select

Manual

Email—to send feedback directly to Technical Publications:

[email protected]

Web—to complete a survey about this Thermo Scientific document:

www.surveymonkey.com/s/PQM6P62

Summary of Contents for Agilent 1200 Series



























































Search results

Summary of Contents for Agilent 1200 Series

Reviews:

Related manuals for Agilent 1200 Series

Brands by name

Popular brands

Thermo Scientific Agilent 1200 Series, Getting Connected Manual

Search results

Summary of Contents for Agilent 1200 Series

Reviews:

Related manuals for Agilent 1200 Series

Brands by name

Popular brands