30
INS248
Reset and Service Messages
When the system requires attention because of a potential
problem, the display will show one of three service
messages. These messages can also be accessed at any
time, allowing the user to view installer information.
!
These messages would normally be programmed
with the telephone numbers of the installer or the
Alarm Receiving Centre (see page 48 for details).
To display the service messages, proceed as follows:
The display will normally show the time and date:
!!!!
!"#$!%&!'()!*%%+
Press
!
followed by
#
for the
Service
message:
,(--!.-()/!,01
!!20)!3$)456$
Press
!
followed by
$
for the
Reset
message:
,(--!78958$$)!:0
!!;$<$:!3=<:$/
Press
!
followed by
%
for the
Anti-code
message:
,(--!.;,!:0
;$<$:!3=<:$/
Press
-
to exit from the message, the display will then
return to normal.
When alarm information is being displayed, pressing the
SCROLL key will slow down the display and also allow
manual scrolling through the events.
Fault Warning Tones
When a fault condition occurs i.e. mains fail, line fault etc.
the internal sounders will chime every 30 seconds for 3
minutes. The chiming will automatically stop when a valid
User code is entered, when
-
is pressed or after 3
minutes (whichever occurs first). The fault indication will
only be cleared from the display when the fault has been
rectified i.e. power, telephone line has been restored.
Other Messages
.-()/!78958$$)
>0)?589!@8!35:$
The alarm engineer has logged into the
programming menu and is working on
site (this message will clear when the
engineer logs off or the system is armed).
,08A5)/!B$456$<
!"#$!%&!'()!*%%+
The number of devices connected to the
networks has changed from the last time
a ‘Confirm Devices’ was done.
;$/0:$!C$=D(E!5<
80F!G@,C7B!0#:
To many invalid code attempts have
caused the keypad to lock out. The
keypad will remain like this for 5 minutes.
H0#!8$$E!(!#<$)
:0!$8(I-$!(66$<<
Engineer access has been programmed
for Engineer code + User code (see
page 44 for details).
Fault Messages
3$)456$!;$J#5)$E
!"#$!%&!'()!*%%+
The service timer has expired indicating
that the system requires a service, zones
that have been placed on test have failed
the test or a fault has occurred that
requires attention (the system can
normally still be used). Contact your
alarm company to advise.
'(58<!K0F$)!@AA
!"#$!%&!'()!*%%+
There is a Mains failure (the keypad may
chime every minute, enter a valid code to
stop the chime). The display will
automatically clear when mains is
reapplied.
KL08$!G58$!2(#-:
!"#$!%&!'()!*%%+
There is a Phone Line fault (the keypad
may chime every minute, enter a valid
code to stop the chime). The display will
automatically clear when line fault clears.
!M!N@!O.""7;H!M
!"#$!%&!'()!*%%+
The Standby Battery has not been
connected, the display will automatically
clear after 1 minute.
O(::$)=!2(#-:
!"#$!%&!'()!*%%+
There is a fault with the control panel
standby battery.
K(8$-!G5E!"(/D$)
!"#$!%&!'()!*%%+
There is a fault with the control panel lid
tamper.
O$--!"(/D$)
!"#$!%&!'()!*%%+
There is a fault with the bell tamper on
the control panel.
.#P5-5()=!"(/D$)
!"#$!%&!'()!*%%+
There is a fault with the auxiliary tamper
on the control panel.
O$--!2#<$!O-0F8
!"#$!%&!'()!*%%+
The bell/Strobe PTC has failed
.#P1!2#<$!O-0F8
!"#$!%&!'()!*%%+
The 12V Auxiliary PTC has failed
;CK!Q!"(/D$)
!"#$!%&!'()!*%%+
There is a fault with the lid tamper of
Keypad X.
;CK!Q!G0<:
!"#$!%&!'()!*%%+
Keypad X has been lost off of the system.
7QK!Q!"(/D$)
!"#$!%&!'()!*%%+
There is a fault with the lid tamper of
Expander X
7QK!Q!G0<:
!"#$!%&!'()!*%%+
Expander X has been lost off of the
system.
7QK!Q!G0!R0-:<
!"#$!%&!'()!*%%+
The voltage at expander X is very low.
7QK!O$--!"(/D!Q
!"#$!%&!'()!*%%+
The expander’s Bell input (that is
programmed as bell tamper) is in fault.
7QK!.#P!"(/D!Q
!"#$!%&!'()!*%%+
The expander’s Auxiliary input (that is
programmed as aux tamper) is in fault.
