manualshive.com logo in svg

Texas Instruments TMS320x281 series, Reference Manual

Share
Download
Texas Instruments TMS320x281 series Reference Manual Download Page 28

2.3

Transmission-Request Set Register (CANTRS)

Transmission-Request Set Register (CANTRS)

www.ti.com

When mailbox

n

is ready to be transmitted, the CPU should set the TRS[

n

] bit to 1 to start the

transmission.

These bits are normally set by the CPU and cleared by the CAN module logic. The CAN module can set
these bits for a remote frame request. These bits are reset when a transmission is successful or aborted.
If a mailbox is configured as a receive mailbox, the corresponding bit in CANTRS is ignored unless the
receive mailbox is configured to handle remote frames. The TRS[

n

] bit of a receive mailbox is not ignored

if the RTR bit is set. Therefore, a receive mailbox (whose RTR is set) can send a remote frame if its TRS
bit is set. Once the remote frame is sent, the TRS[

n

] bit is cleared by the CAN module. Therefore, the

same mailbox can be used to request a data frame from another mode. If the CPU tries to set a bit while
the eCAN module tries to clear it, the bit is set.

Setting CANTRS[

n

] causes the particular message

n

to be transmitted. Several bits can be set

simultaneously. Therefore, all messages with the TRS bit set are transmitted in turn, starting with the
mailbox having the highest mailbox number (= highest priority), unless TPL bits dictate otherwise.

The bits in CANTRS are set by writing a 1 from the CPU. Writing a 0 has no effect. After power up, all bits
are cleared.

Figure 2-3. Transmission-Request Set Register (CANTRS)

31

0

TRS[31:0]

RS-0

LEGEND: RS = Read/Set; -

n

= value after reset

Table 2-3. Transmission-Request Set Register (CANTRS) Field Descriptions

Bit

Field

Value

Description

31:0

TRS[31:0]

Transmit-request-set bits

1

Setting TRS

n

transmits the message in that mailbox. Several bits can be set simultaneously with all

messages transmitted in turn.

0

No operation

eCAN Registers

28

SPRU074F – May 2002 – Revised January 2009

Submit Documentation Feedback

Summary of Contents for TMS320x281 series





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands