Texas Instruments TMS320C645X User Manual Download Page 58 | Manualshive

Page: 58 / 218

background image

www.ti.com

Descriptor

Descriptor

Buffer

Buffer

Port Tx DMA

State

Tx Queue Head Descriptor

Pointer

SRIO Functional Description

Figure 25. TX Buffer Descriptor

Start Message Passing

SRIO_REGS->Queue0_RXDMA_HDP

= (int )RX_DESCP0_0 ;

SRIO_REGS->Queue0_TxDMA_HDP

= (int )TX_DESCP0_0 ;

2.3.5

Maintenance

The type 8 MAINTENANCE packet format accesses the RapidIO capability registers (CARs), command
and status registers (CSRs), and data structures. Unlike other request formats, the type 8 packet format
serves as both the request and the response format for maintenance operations. Type 8 packets contain
no addresses and only contain data payloads for write requests and read responses. All configuration
register read accesses are word (4-byte) accesses. All configuration register write accesses are also word
(4-byte) accesses.

The wrsize field specifies the maximum size of the data payload for multiple double-word transactions.
The data payload may not exceed that size but may be smaller if desired. Both the maintenance read and
the maintenance write request generate the appropriate maintenance response.

The maintenance port-write operation is a write operation that does not have guaranteed delivery and
does not have an associated response. This maintenance operation is useful for sending messages such
as error indicators or status information from a device that does not contain an endpoint, such as a switch.
The data payload is typically placed in a queue in the targeted endpoint and an interrupt is typically
generated to a local processor. A port-write request to a queue that is full or busy servicing another
request may be discarded.

SRIO_REGS->LSU1_Reg0 =

CSL_FMK( SRIO_LSU1_REG0_RAPIDIO_ADDRESS_MSB,0 );

SRIO_REGS->LSU1_Reg1 =

CSL_FMK( SRIO_LSU1_REG1_ADDRESS_LSB_CONFIG_OFFSET, (int )car_csr );

SRIO_REGS->LSU1_Reg2 =

CSL_FMK( SRIO_LSU1_REG2_DSP_ADDRESS, (int )&xmtBuff[0]);

SRIO_REGS->LSU1_Reg3 =

CSL_FMK( SRIO_LSU1_REG3_BYTE_COUNT,byte_count );

//=4

SRIO_REGS->LSU1_Reg4 =

CSL_FMK( SRIO_LSU1_REG4_OUTPORTID,0 )|

//0b00

CSL_FMK( SRIO_LSU1_REG4_PRIORITY,0 )|

//0b00

CSL_FMK( SRIO_LSU1_REG4_XAMBS,0 )|

//no extended address

CSL_FMK( SRIO_LSU1_REG4_ID_SIZE,1 )|

//tt = 0b01

CSL_FMK( SRIO_LSU1_REG4_DESTID,0xBEEF )|

//0xBEEF

CSL_FMK( SRIO_LSU1_REG4_INTERRUPT_REQ,0 );

//0 = event-driven, 1 = poll

SRIO_REGS->LSU1_Reg5 =

CSL_FMK( SRIO_LSU1_REG5_DRBLL_INFO,0x0000 )|

CSL_FMK( SRIO_LSU1_REG5_HOP_COUNT,0x03 )|

//hop = 0x03

CSL_FMK( SRIO_LSU1_REG5_PACKET_TYPE,type );

//type = REQ_MAINT_RD

Serial RapidIO (SRIO)

58

SPRU976 – March 2006

Submit Documentation Feedback

«
...
56
57
58
59
60
...
»

Summary of Contents for TMS320C645X



























































































































































































































Reviews:

No comments

Related manuals for TMS320C645X

Brand: BEIER-Electronic Pages: 22

Brand: OES Pages: 3

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Eaton Pages: 4

Brand: Linear Technology Pages: 7

J1000 CIMR-JC series

Brand: YASKAWA Pages: 25

Controller CR100

Brand: Sonos Pages: 12

Brand: Qorvo Pages: 6

Brand: U-Tron Pages: 8

Brand: Black Stone Pages: 2

Brand: Vega Pages: 28

Brand: WATSON Pages: 16

Brand: Danfoss Pages: 16

Dynamic Boiler Controller

Brand: Intiel Pages: 25

Brand: Rain Bird Pages: 20

Brand: GEM Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands