manualshive.com logo in svg

Texas Instruments MSP50C614, User Manual

The Texas Instruments MSP50C614 is a high-performance integrated circuit featuring advanced functionalities. To easily set up and operate this device, a comprehensive User Manual is available for free download at manualshive.com. This manual provides concise instructions and essential information to maximize the potential of the MSP50C614.

Share
Download
background image

Instruction Classification

4-27

Assembly Language Instructions

Table 4–15. Class 1b Instruction Description

C1b

Mnemonic

Description

0

0

0

0

OR A

n, {adrs}

ORS A

n, {adrs}

Logical  OR the contents of the data memory location in {

adrs}

and the selected accumulator.  Result(s) stored in
accumulator(s). ALU status is modified

0

0

0

1

AND A

n, {adrs}

ANDS A

n, {adrs}

Logical AND the contents of the data memory location in {

adrs}

and the accumulator. Result(s) stored in accumulator(s). ALU
status is modified

0

0

1

0

XOR A

n, {adrs}

XORS A

n, {adrs}

Exclusive OR the contents of the data memory location in
{

adrs} and the accumulator. Result(s) stored in accumulator(s).

ALU status is modified

0

0

1

1

MOVB A

n, {adrs}

8

MOVBS A

n, {adrs}

8

Load the contents of the data memory location in {

adrs}and to

the lower 8 bits of the accumulator. Zero fill the upper byte in the
accumulator ALU status is modified.

0

1

0

0

MOVB {

adrs}

8

, A

n

MOVBS {

adrs}

8

, A

n

Store the lower 8 bits of accumulator to the data memory
location in {

adrs}. The data byte is automatically routed to either

the lower byte or upper byte in the 16 bit memory word based on
the LSB of the address. Transfer status is modified.

0

1

0

1

Reserved

N/A

0

1

1

0

CMP A

n, {adrs}

CMPS A

n, {adrs}

Store the arithmetic status of the contents of {

adrs} subtracted

from accumulator into the ALU status bits.  The accumulator is
not modified.

0

1

1

1

MOV {

adrs} , *An

MOVS {

adrs} , *An

Look up the value stored in program memory addressed by the
accumulator and store in the data memory location in {

adrs}.

Transfer status is modified .

1

0

0

0

MULTPL A

n, {adrs}

MULTPLS A

n, {adrs}

Multiply the MR register by the contents of {

adrs} and transfer

the lower 16 bits of the result to the accumulator. Latch the
upper 16 bits into the PH register. ALU status is modified.

1

0

0

1

MOVSPH A

n, MR, {adrs}

MOVSPHS A

n, MR, {adrs}

Load the MR register in signed mode from the data memory
location in {

adrs}. In parallel, subtract the PH register from the

accumulator. The string bit will string with the previous ALU
status (CF, ZF)  but it will not load the string counter (executes
once). ALU status is modified.

1

0

1

0

MOVAPH A

n, MR, {adrs}

MOVAPHS A

n, MR, {adrs}

Load the MR register in signed mode from the data memory
location in {

adrs}. In parallel, add  the PH register  to the

accumulator. The string bit will string with the previous ALU
status (CF, ZF) but it will not load the string counter (executes
once). ALU status is modified.

Summary of Contents for MSP50C614































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSP50C614

MAGIMIX DOUGH BOWL Manual preview
DOUGH BOWL
Brand: MAGIMIX Pages: 10
IEI Technology WAFER-C400EV User Manual preview
WAFER-C400EV
Brand: IEI Technology Pages: 45
Klarstein 10035479 Manual preview
10035479
Brand: Klarstein Pages: 36
Hamilton Beach 70550R - PROCTOR Silex 350W 2 Speed Food Processor Use & Care Manual preview
70550R - PROCTOR Silex 350W 2 Speed Food Processor
Brand: Hamilton Beach Pages: 44
Hamilton Beach 70740 Use & Care Manual preview
70740
Brand: Hamilton Beach Pages: 40
Nemco Easy Chopper 3 Operating And Maintenance Instructions preview
Easy Chopper 3
Brand: Nemco Pages: 2
Vitek VT-1606 Manual Instruction preview
VT-1606
Brand: Vitek Pages: 8
cecotec CHOPBEAT 1500 Instruction Manual preview
CHOPBEAT 1500
Brand: cecotec Pages: 76
Nakanishi NDSR660A User Manual preview
NDSR660A
Brand: Nakanishi Pages: 16
Lagrange GLACES CREATIV Instruction Book preview
GLACES CREATIV
Brand: Lagrange Pages: 47
Kalorik USK HA 33143 Operating Instructions Manual preview
USK HA 33143
Brand: Kalorik Pages: 17
MAGIMIX Ma Cuisine Instructions For Use Manual preview
Ma Cuisine
Brand: MAGIMIX Pages: 79
Vdwall LVP615U User Manual preview
LVP615U
Brand: Vdwall Pages: 112
Team Kalorik TKG MC 1000 Manual preview
TKG MC 1000
Brand: Team Kalorik Pages: 36
Currys C72MFP11 Instruction Manual preview
C72MFP11
Brand: Currys Pages: 17
KitchenAid KFPW763OB Parts List preview
KFPW763OB
Brand: KitchenAid Pages: 5
KitchenAid KFP0922WH0 Owner'S Manual preview
KFP0922WH0
Brand: KitchenAid Pages: 5
KitchenAid KFC3100BU1 Parts List preview
KFC3100BU1
Brand: KitchenAid Pages: 3

Brands by name

Popular brands

Load more brands