Texas Instruments ADC12DL3200 User Manual Download

Page: 2 / 24

SLAU776 – May 2018

Contents

Contents

Preface

........................................................................................................................................

Equipment

...........................................................................................................................

1.1

Evaluation Board Feature Identification Summary

......................................................................

1.2

Required Equipment

.........................................................................................................

Setup Procedure

..................................................................................................................

2.1

Install the High Speed Data Converter (HSDC) Pro Software

.........................................................

2.2

Install the Configuration GUI Software

....................................................................................

2.3

Connect the EVM and TSW14DL3200EVM

..............................................................................

2.4

Connect the Power Supplies to the Boards (Power Off)

...............................................................

2.5

Connect the Signal Generators to the EVM (*RF Outputs Disabled Until Directed)

..............................

2.5.1

If External Clocking is Used (Optional)

.........................................................................

2.6

Turn On the TSW14DL3200EVM Power and Connect to the PC

...................................................

2.7

Turn On the ADC12DL3200EVM 5-V Power Supply and Connect to the PC

......................................

2.8

Turn On the Signal Generator RF Outputs

.............................................................................

2.9

Open the ADC12DL3200EVM GUI and Program the ADC and Clocks

............................................

2.10

Calibrate the ADC Device on the EVM

..................................................................................

2.11

Open the HSDC Software and Load the FPGA Image to the TSW14DL3200EVM

...............................

2.12

Capture Data Using the HSDC Pro Software

..........................................................................

Device Configuration

..........................................................................................................

3.1

Tab Organization

...........................................................................................................

3.2

Low-Level Control

..........................................................................................................

Troubleshooting the ADC12DL3200EVM

...............................................................................

Optional ADC12DL3200EVM Configurations

..........................................................................

B.1

Modifying the EVM for Optional Clocking Support

.....................................................................

Summary of Contents for ADC12DL3200

























Search results

Summary of Contents for ADC12DL3200

Reviews:

Related manuals for ADC12DL3200

Brands by name

Popular brands

Texas Instruments ADC12DL3200, User Manual

Search results

Summary of Contents for ADC12DL3200

Reviews:

Related manuals for ADC12DL3200

Brands by name

Popular brands