TermaCook Integral 800 Instructions For Fitting And Use Download Page 39

Page: 39 / 48

Terma

Cook

Instructions for assembly

Safety instructions for kitchen unit fitters

· Veneers, adhesives and plastic surfaces of surrounding

furniture must be temperature resistant (>75°C). If the

veneers and surfaces are not sufficiently heat resistant

they may become deformed.

· Ensure that all live connections are safely insulated when

installing the hob.

· Cover strips between the wall and the worktop behind the

hob which are made of solid wood are permissible as

long as minimum clearances in accordance with the

installation diagrams are maintained.

· Minimum clearances of the hob cut-out towards the rear

are to be maintained in accordance with the installation

diagram.

· For installation directly next to a tall cupboard, a safety

distance of at least 50 mm must be ensured. The side

surface of the tall cupboard should be fitted with heat

resistant material. Due to working requirements, however,

the distance should be at least 300 mm.

· The packaging materials (plastic foil, polystyrene, nails

etc.) must be kept out of reach of children as these parts

are potentially dangerous. Small parts can be swallowed

and there is a danger of plastic sheeting causing suffoca-

tion.

Ventilation

· The induction hob is equipped with a ventilator. The venti-

lator switches on or off automatically. If the temperature

produced by the electronic device exceeds a certain

level, the ventilator turns on in low speed. In case the

induction hob is being used intensively, the ventilator swit-

ches to a higher speed. If the electronics was cooled

sufficiently, the ventilator reduces the speed and switches

off automatically.

· Clearance between the induction hob and kitchen furni-

ture or built-in units must provide for sufficient ventilation of

the induction hob.

· If the power level of a cooking zone is automatically rai-

sed or lowered (see section on thermal cut-off device) it is

likely that the cooling system does not cool sufficiently. In

this case we recommend that the back wall of the bot-

tom kitchen unit in the area of the worktop cut-out be

opened and that the front transverse strip of the unit be

removed over the entire width of the appliance in order

to promote the circulation of air.

In order to better ventilate
the hob, an air gap of at
least 5 mm should be left
at the front.

Installation

Important

· Remove any transverse strips underneath the worktop at

least in the area of the worktop cut-out.

· When installing the appliance on top of a drawer it is

essential to ensure that no sharp items are stored in the

drawer since these could become bent on the underside

of the hob and prevent the drawer from being opened

and closed.

· If a shelf has been inserted underneath the hob, there

must be a clearance of at least 20 mm to the underside

of the hob in order to ensure that the hob is sufficiently

ventilated.

· To avoid danger of fire, make sure that no combustible

objects which could easily catch fire or become de

formed on exposure to heat are directly next to or under

the surface.

Sealing of the hob

Before installation, correctly insert the sealing unit delivered with
the hob.

· No liquids may penetrate between the edge of the hob

and the worktop or between the hob and the wall and

come into contact with any electrical appliances.

· When installing a hob into an uneven worktop, e.g. with a

ceramic or similar covering (tiles etc.), the seal on the hob

is to be removed and the seal between the hob and

worktop made with plastic sealing materials (putty).

· The hob must under no circumstances be sealed with

silicone sealant! This would make it impossible to remove

the hob at a later date without damaging it.

Working surface cut-out

Cut out the worktop recess accurately with a good, straight saw
blade or recessing machine. The cut edges should then be
sealed so that no moisture can penetrate.
The area is cut out as illustrated. The glass ceramic hob must
have a level and flush bearing. Any distortion may lead to
fracture of the glass panel. Make sure that the sealing of the hob
is properly seated.