Terex TS14G, Maintenance Manual

Page: 47 / 376

3
Section 110-0130
SM 1693 Rev1 03-04
Engine - Power Takeoff - Tractor
2. Using suitable lifting equipment, position triple pump
over its mounting studs and secure with nuts and
lockwashers removed during removal.
3. Reconnect driveline to flange (18). Refer to
Section 130-0010, DRIVELINE.
4. Remove oil level plug from PTO cover (10) and fill
PTO assembly with lubricant specified in
Section 300-0020, LUBRICATION SYSTEM, until oil
flows from the oil level port. Install oil level plug in PTO
cover (10) and tighten securely.
5. Place the battery master switch in the 'On' position,
start the engine and bring oil to correct operating
temperature. Check for leaks and correct as necessary.
6. Remove wheel blocks from all road wheels.
MAINTENANCE
Numbers in parentheses refer to Fig. 1.
Note: Refer to Section 300-0020, LUBRICATION
SYSTEM for recommended check and drain intervals
and lubricant specifications.
Oil Level Check
Remove oil level plug from the PTO cover (10) and, if
oil level is below the bottom of the filler hole, add
lubricant until it flows from the filler hole. Reinstall oil
level plug and tighten securely.
Drain and Refill
To drain:
Remove drain plug (30) from PTO cover (10)
and drain oil into a suitable container. Reinstall drain
plug (30) securely when draining is complete.
To refill:
Remove oil level plug from the PTO cover
(10) and fill PTO assembly with lubricant specified in
Section 300-0020, LUBRICATION SYSTEM, until oil
flows from the oil level port. Install oil level plug in PTO
cover (10) and tighten securely.
SPECIAL TOOLS
There are no special tools required for procedures
outlined in this section. Refer to Section 300-0070,
SERVICE TOOLS, for part numbers of general service
tools required. These tools are available from your
dealer.
2. Install new oil seal (1) in centre bore of flywheel
cover case (2) so that it is flush with flywheel cover
case (2) face.
Note:
When installing new oil seals, install them with
the oil lip (larger of the two lips with the spring behind
it) facing inward. Care should be taken to prevent
damage to seal lips during assembly.
3. Press bearings (4 & 29) into their bores in flywheel
cover case (2).
4. Press bearings (7 & 27) into their respective bores in
PTO cover (10). Turn PTO cover (10) over and install
snap rings (21).
5. Install new oil seal (19) into centre bore in PTO
cover (10) so that it is flush with PTO cover (10) face.
6. Install driven gear (28) and driveshaft (6) into
flywheel cover case (2). Slide drive gear (5) over
driveshaft (6) to its proper location.
7. Install new gasket (26) on PTO cover (10) and
assemble PTO cover (10) to flywheel cover case (2).
Secure PTO cover (10) to flywheel cover case (2) with
bolts (8 & 24).
8. Install flange (18), hardened washer (17) and locknut
(16) on driveshaft (6) end. Tighten locknut (16) to a
torque of 950 - 1 085 Nm (700 - 800 lbf ft), lubricated
and install cotter pin (15).
INSTALLATION
Numbers in parentheses refer to Fig. 1.
Note: When reassembling PTO assembly to engine
flywheel housing, and triple pump to PTO assembly, be
sure to align match marks inscribed during
disassembly.
Note: Tighten all fasteners without special torques
specified to standard torques listed in
Section 300-0080, STANDARD BOLT AND NUT
TORQUE SPECIFICATIONS.
1. Install spacer (31) on PTO assembly and, using
suitable lifting equipment, position PTO assembly on
engine flywheel housing. Secure the PTO assembly
and spacer (31) to the engine flywheel housing with
bolts (3) and lockwashers (22). Tighten bolts (3) to a
torque of 54 - 60 Nm (40 - 44 lbf ft), lubricated.
Courtesy of Machine.Market