![Terex TS14G Maintenance Manual Download Page 223](http://html1.mh-extra.com/html/terex/ts14g/ts14g_maintenance-manual_1088883223.webp)
Section 235-0030
SM 1895 1-00
3
8. Engage end cap (13) and outer cylinder (1) thread
and screw up fully. Tighten end cap (13) to a torque
of 338 - 407 Nm (250 - 300 lbf ft).
9. Re-drill location hole for lock ring (12), diameter
3.175 mm (0.125 in) x 10 mm (0.394 in) maximum
depth. Install lock ring (12).
INSTALLATION
Ejector Cylinder
Note:
Tighten all fasteners to standard torques listed
in Section 300-0080, STANDARD BOLT AND NUT
TORQUE SPECIFICATIONS.
Note:
Tighten all hydraulic lines fitted with ORFS
connections, as described in Section 235-0000,
HYDRAULIC SYSTEM SCHEMATIC.
WARNING
To prevent personal injury and property
damage, be sure lifting equipment is properly
secured and of adequate capacity to do the job
safely.
1. Install a suitable strap, or other lifting device,
around cylinder assembly and position cylinder in tail
assembly, ready for mounting.
Note:
Oil inlet port must be towards the ground.
2. Secure piston tube end of cylinder to the ejector
lever and the base end of cylinder to the bracket on
the tail frame with mounting pins and secure with
bolts, lockwashers and nuts.
Bowl Hydraulic System - Ejector Cylinder
3. Remove caps from cylinder port and hose end and
install new 'O' ring on hose. Install hose to cylinder
inlet port.
4. Lubricate mounting pins at lube fittings. Refer to
Section 300-0020, LUBRICATION SYSTEM.
5. Check oil level in hydraulic tank and add oil if low.
Refer to Section 235-0040, HYDRAULIC TANK, for
correct fill level. Refer to Section 300-0020,
LUBRICATION SYSTEM, for the type of oil used.
6. Place the battery master switch in the 'On'
position, start the engine and operate the ejector
controls. Check hydraulic lines and fittings for leaks.
Tighten lines and fittings as required.
7. Remove wheel blocks.
MAINTENANCE
Inspect ejector cylinder regularly for leaks or
damage, repair as required. Lubricate cylinder pins
every 50 hours, as specified in Section 300-0020,
LUBRICATION SYSTEM.
SPECIAL TOOLS
There are no special tools required for procedures
outlined in this section. Refer to Section 300-0070,
SERVICE TOOLS, for part numbers of general
service tools and adhesives required. These tools
and adhesives are available from your dealer.
* * * *
SPECIAL TORQUE SPECIFICATIONS
TORQUE
FIG. NO.
ITEM NO.
ITEM NAME
Nm
lbf ft
1
13
End Cap
338 - 407
250 - 300
Summary of Contents for TS14G
