Service and Repair Manual
October 2018
Boom Components
84
Z®-135
/70
Part No. 1268557GT
9
Press and hold the
enter
button on the ground
control panel while pulling out the ground
controls red Emergency Stop button to the on
position. Hold the
enter
button for
approximately 5 seconds and then release it.
10 Enter sensor calibration mode by pressing the
buttons at the ground controls in the following
sequence:
(plus)(enter)(enter)(plus)
.
11 Press the
enter
or
previous
button on the
LCD screen until DELETE PRIMARY BOOM
ANGLE SENSOR CALIBRATION is displayed.
12 Press the
plus
button to select YES, then
press the
enter
button to accept.
13 Place a digital level that has been calibrated to
gravity on top of the primary boom and note
the angle displayed on the digital level.
14 At the PRIMARY BOOM ANGLE TO GRAVITY
0.0 DEG screen, press the
plus
button or
minus
button to adjust the display to the exact
value shown on the digital level, then press the
enter
button.
Note: If the measured angle already matches the
angle shown on the display at the ground controls,
press the
plus
button or
minus
button to change
the angle and then change back to the measured
value. The system must detect a change in
displayed value to record the calibrated value.
15 Start the engine from the ground controls.
Note: If the system exits out of calibration mode
when the engine is started, repeat step 8 and then
continue with step 14.
16 Fully raise the secondary boom. The boom is
fully raised when the cylinder is fully extended
and the boom stops moving.
17 Press and hold a function enable/speed select
button and the primary boom down button and
lower the primary boom down until the digital
level displays -50 degrees.
18 At the ground controls, press the
plus
button
or
minus
button to adjust the display to the
exact value shown on the digital level and
press the
enter
button.
Note: Be sure the number entered at the ground
controls is a negative number.
Note: If the measured angle already matches the
angle shown on the display at the ground controls,
press the
plus
button or
minus
button to change
the angle and then change back to the measured
value. The system must detect a change in
displayed value to record the calibrated value.
19 Press and hold a function enable/speed select
button and the primary boom up button until
the digital level displays -20 degrees.
20 At the ground controls, press the
plus
button
or
minus
button to adjust the display to the
exact value shown on the digital level and
press the
enter
button.
Note: Be sure the number entered at the ground
controls is a negative number.
Note: If the measured angle already matches the
angle shown on the display at the ground controls,
press the
plus
button or
minus
button to change
the angle and then change back to the measured
value. The system must detect a change in
displayed value to record the calibrated value.
21 Press and hold a function enable/speed select
button and the primary boom up button until
the digital level displays 10 degrees.
Summary of Contents for Genie Z-135/70
