Service and Repair Manual
December 2019
Boom Components
66
SX
™
-150
Part No. 1300669GT
Note: Use the following chart to identify the
description of each LCD screen control button used
in this procedure.
Plus
Minus
Previous
Enter
1 Push in the ground controls red Emergency
Stop button to the off position.
2 Turn the key switch to ground controls.
3 Open the ground control box.
4 Locate the calibration toggle switch at the top
of the ground control box. Activate calibration
mode by moving the toggle switch in the left
direction.
5 Temporarily install a control box door retaining
fastener between the door and the box to
prevent the control box door from moving the
toggle switch while calibrating the machine.
6 Remove the key from the main key switch.
Insert the key into the bypass/recovery key
switch and turn it to the bypass position.
Note: The angle sensor calibration values will not
be saved correctly unless the key switch is in the
bypass position and the calibration toggle switch is
activated.
7 Press and hold the
enter
button on the ground
control panel while pulling out the ground
controls red Emergency Stop button to the on
position. Hold the
enter
button for
approximately 5 seconds and then release it.
8 Enter sensor calibration mode by pressing the
buttons at the ground controls in the following
sequence:
(plus)(enter)(enter)(plus)
.
9 Press the
enter
or
previous
button on the
LCD screen until DELETE PRIMARY BOOM
ANGLE SENSOR is displayed.
10 Press the
plus
button to select YES, then
press the
enter
button to accept.
11 Place the digital level on top of the primary
boom near the pivot and note the angle
displayed on the digital level.
12 Press the
enter
button until PRIMARY BOOM
ANGLE TO GRAVITY -2.6 DEG is displayed,
press the
plus
or
minus
button to adjust the
display to the exact value shown on the digital
level, then press the
enter
button.
Note: If the measured angle already matches the
angle shown on the display at the ground controls,
press the
plus
button or
minus
button to change
the angle and then change back to the measured
value. The system must detect a change in
displayed value to record the calibrated value.
Note: If the system exits out of calibration mode
when the engine is started, repeat step 8 and
continue to step 13.
13 Start the engine from the ground controls.
14 Press and hold a function enable/speed select
button and the primary boom up button until
the digital level displays 15 degrees.
15 At the PRIMARY BOOM ANGLE TO
GRAVITY 15 DEG screen, press the
plus
or
minus
button to adjust the display to the exact
value shown on the digital level, then press the
enter
button.
Note: If the measured angle already matches the
angle shown on the display at the ground controls,
press the
plus
button or
minus
button to change
the angle and then change back to the measured
value. The system must detect a change in
displayed value to record the calibrated value.
16 Press and hold a function enable/speed select
button and the primary boom up button until
the digital level displays 32 degrees.
Summary of Contents for Genie SX-150
