Terex Genie Lift Connect Installation Instructions Manual Download Page 54

Page: 54 / 67

Instructions

Rev C

GTH

™

Models

Lift Connect

™

Part No. 1295251GT

7 Connect the wiring adapter harness to the 8

pin connector located at the front right corner

under the dashboard.
Genie part number 55.0602.1184GT.

Note: Harness connectors are keyed for proper

installation.

Component damage hazard.

Improper connections will result

in damage to the telematics

module and it is not covered

under warranty.

example of keyed harness connector

8 Connect the telematics module to the wiring

adapter harness.

9 Route the loose end of the wiring adapter

harness with the ring terminal through the

dashboard towards the fuse panel.

10 Connect the ring terminal to the J2 terminal on

the fuse panel.

Note: The J2 terminal is the center terminal with

the red boot.

11 Secure the harness to the existing cables

using the provided cable ties.
Genie part number 21121GT.

Summary of Contents for Genie Lift Connect




































































Search results

Summary of Contents for Genie Lift Connect

Reviews:

Related manuals for Genie Lift Connect

Brands by name

Popular brands

Terex Genie Lift Connect, Installation Instructions Manual

Search results

Summary of Contents for Genie Lift Connect

Reviews:

Related manuals for Genie Lift Connect

Brands by name

Popular brands